User manual CHAMBERLAIN LA400

[. . . ] INSTALLATION/OPERATION MANUAL MODEL LA400 MEDIUM DUTY SWING GATE OPERATOR Radio Receiver Built on Board 315MHz 2 YEAR WARRANTY Serial # Primary Arm Serial # Secondary Arm Serial # Control Box Installation Date TABLE OF CONTENTS Introduction 2-5 Carton Inventory . . 33 Operation 34 Overview of Typical Installation 6-10 Reset Button . . 7 Safety Precautions for Swing and Ornamental "Grill Type Gates" . . 10 Maintenance Basic Control Board Layout Wiring Diagram Troubleshooting Repair Parts LA400 Swing Gate Accessories Warranty Policy and Service 35-36 37 38 39-40 41-42 43 44 Battery Replacement . [. . . ] The Save switch must be set to the OFF position prior to programming or changing the switches. NOTE: Save switch must be in the OFF position prior to programming or changing switches for the change to be saved. O N OFF OFF SINGLE NO NO ON ON DUAL NC NC SAVE MAGLOCK MODE EDGE PHOTO 12345 S1 FACTORY DEFAULT SHOWN P2 J19 Ø14GPØ89ØE Ø14LGØ89ØE Ø14SKØ89ØE J1 CLOSE EDGE OPEN/EGE PHOTO L1 1 O N S8 LEARN XMITTER 2 OFF OFF SINGLE NO NO S1 ON SAVE ON MAGLOCK DUAL MODE NC EDGE NC PHOTO 12345 OPEN PHOTO CLOSE PHOTO GATE1 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS 24V GATE 2 OVLD SWITCHED ACCESSORY POWER GATE 1 GATE 1 AND GATE 2 O N O N OFF OFF SINGLE NO NO ON ON DUAL NC NC 24 OFF OFF SINGLE NO NO ON ON DUAL NC NC 12345 12345 Step 2: Program Limits (Ensure Save Switch is in the OFF position before beginning) DIAGNOSTIC 1. With the gate in the closed position, press the "LEARN LIMITS" button. The "SET OPEN LIMIT" LED will blink. GATE 1 SET T EN N OPEN T LIMIT SET CLOSE LIMIT LEARN LIMITS GATE 2 FORCE LEARN LIMITS Button DIAGNOSTIC GATE 1 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS 2. Use the "Gate 1" buttons to move Gate 1 to the desired open position (not to exceed 100°). If you have gone beyond the desired open position you can jog the gate towards the close position by using the opposite Gate 1 button. Repeat if Gate 2 is present using the "Gate 2" buttons. DIAGNOSTIC DIAGNOSTIC GATE 1 GATE 1 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS GATE 2 GATE 2 FORCE FORCE GATE 2 DIAGNOSTIC P2 J19 Ø14GP 89ØE 14GPØ89 Ø14LG 89ØE 14LGØ89 Ø14SK 89ØE 14SKØ89 J1 CLOSE EDGE OPEN/EGE PHOTO L1 FORCE 1 S8 LEARN XMITTER 2 OFF OFF SINGLE NO NO ON SAVE ON MAGLOCK DUAL MODE EDGE NC PHOTO NC OPEN PHOTO S1 CLOSE PHOTO GATE1 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS 24V GATE 2 OVLD SWITCHED ACCESSORY POWER SINGLE BUTTON 3. Press the "LEARN LIMITS" button again to set the Open position. The "SET CLOSE LIMIT" LED will blink and beep once. GATE 1 O N 12345 SET OPEN LIMIT SET S CLO C CLOSE L LIMIT LEARN LIMITS GATE 2 FORCE 4. Use the "Gate 1" buttons to move Gate 1 to the desired close position. If you have gone beyond the desired closed position you can jog the gate towards the open position by using the opposite Gate 1 button. Repeat if Gate 2 is present using the "Gate 2" buttons. DIAGNOSTIC DIAGNOSTIC GATE 1 GATE 1 SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS SET OPEN LIMIT SET CLOSE LIMIT LEARN LIMITS GATE 2 GATE 2 FORCE FORCE DIAGNOSTIC SINGLE BUTTON O SINGLE B 5. Press the "LEARN LIMITS" button again to set the Closed position. The limits are now set. GATE 1 SET OPEN LIMIT SET S CL C CLOSE L LIMIT LEARN LIMITS GATE 2 FORCE 6. Using the single button control on the board, run the gate(s) from the closed position to the open position. This will learn the forces. O N OFF OFF SINGLE NO NO ON ON DUAL NC NC SAVE MAGLOCK MODE EDGE PHOTO 12345 S1 7. Set Save Switch to the ON position. 25 Step 3: Set Force / Bi-Part / Timer P2 J19 Ø14GP 89ØE 14GPØ89 Ø14LG 89ØE 14LGØ89 Ø14SK 89ØE 14SKØ89 J1 CLOSE EDGE BI-PART DELAY Control OPEN/EGE PHOTO L1 1 O N S8 LEARN XMITTER 2 OFF OFF SINGLE NO NO ON SAVE ON MAGLOCK DUAL MODE EDGE NC PHOTO NC 12345 S1 OPEN PHOTO CLOSE PHOTO FORCE Control SET OPEN LIMIT 24V OVLD SWITCHED ACCESSORY POWER FORCE BIPART DELAY TIMER TO CLOSE TIMER TO CLOSE Control FORCE BI-PART DELAY TIMER TO CLOSE Z9 Z8 MIN MAX OFF MAX OFF MAX FORCE CONTROL Set the force control such that the opener will complete a full cycle of gate travel but will reverse off an obstruction without applying an excessive amount of force. BI-PART DELAY Set the BI-PART DELAY to desired setting. NOTE: Used for Dual Gate installations only. TIMER TO CLOSE ENABLE Set the TIMER TO CLOSE to desired setting. The range is 0 to 180 seconds, 0 seconds is OFF. FORCE BI-PART DELAY TIMER TO CLOSE Minimun Force Maximum Force OFF MAX OFF MAX Your basic installation is now complete. 26 OPTIONAL CONTROL AND SAFETY DEVICES To Add or Reprogram a Remote Control 1. Press and release "LEARN XMITTER" button (LED will light up). Press and hold remote button, the LED will flash, alarm will beep twice and the LED will go out. [. . . ] Requires separate power supply (Model ARMPS). OPEN 50-19509 86LM Remote Antenna Mounting Kit: Kit contains antenna bracket and 15' (4. 6 m) of cable. 50-19511 50-19512 GCPSN4 6" Post Mounting Kit for control box 4" Post Mounting Kit for control box 2 1/2" Post Mounting Kit for control box Commercial Protector System®: Maximum range is 45' 24V. Commercial Protector System® (Direct Connect): Maximum range is 45' 24V. Includes mounting hardware. CPS-LN4 43 WARRANTY POLICY AND SERVICE LIFTMASTER® TWO YEAR LIMITED WARRANTY The Chamberlain Group, Inc. [. . . ]