User manual CHAMBERLAIN HC260

[. . . ] Automatic Gate Opener Models , when installed and maintained according to all the Manufacturer's instructions in combination with a Gate, which has also been installed and maintained according to all the Manufacturer's instructions, meets the provisions of EU Directive 89/392/EEC and all amendments. I, the undersigned, hereby declare that the equipment specified above and any accessory listed in the manual conforms to the above Directives and Standards. This safety alert symbol means "Caution" - failure to comply with such an instruction involves risk of personal injury or damage to property. This gate drive mechanism is designed and tested to offer appropriately safe service provided it is installed and operated in strict accordance with the following safety rules. [. . . ] Incorrect installation and/or failure to comply with the following instructions may result in serious personal injury or property damage. When using tools and small parts to install or carry out repair work on a gate exercise caution and do not wear rings, watches or loose clothing. Installation and wiring must be in compliance with your local building and electrical installation codes. Any entrapment possibility by the moving wing between wing & walls must be secured with safety edges or IR-sensors. Please remove any locks fitted to the gate in order to prevent damage to the gate. After the installation a final test of the full function of the system and the full function of the safety devices must be done. This drive cannot be used with a gate incorporating a wicket door unless the drive cannot be operated with the wicket door open. Employ a qualified technician to repair the gate, never attempt to repair it yourself. Disconnect electric power to the system before making repairs or removing covers. A disconnecting device must be provided in the permanently-wired installation to guarantee all-pole disconnection by means of a switch (at least 3mm contact gap) or by a separate fuse. Make sure that people who install, maintain or operate the gate drive and/or the control board are qualified and follow these instructions. Keep these instructions in a safe place so that you can refer to them quickly when you need to. These might be needed later on individual settings in the controls' programming. (refer to JUMPERS) Put the 4 large closure screws of the box through cover of the box. If the lid does not close completely, then the box is not fitted to the wall evenly and is therefore distorted. A) start with still dead 230Volts supply cable on the left side of the box. Then connect ground wire to base plate with washer and nut (exactly as shown in picture detail). we recommend the following accessories: LA400-JB40E Kit for cable extension of one installation unit. Consists of 12m of cable 6-pole with identical colours, distribution box IP65, cable screw joints and fastening material P1 button to program P2 button to program P3 button to program Description of LED's (light-emitting diode) Description Colour green Function monitors emergency switch or safety edge ON: blocks control board OFF: OK key switch ON: key switch is operating OFF: key switch is not operating Photocells 2 ON: OK (active) OFF: no photocell fitted Photocells 1 ON: OK (active) OFF: no photocell fitted learn mode indication ON: learn mode active OFF: learn mode inactive diagnosis mode Refer to FAQ's Brown cable green cable white cable yellow cable Motor2 brown cable green cable white cable yellow cable PHO2 key switch negative pole Photocells 1 Photocells 2 negative pole connector for emergency switch or safety edge with 8. 2KOhms connection for 801719 radio receiver connection for E-lock control board 24V power input from transformer. EN12453 specifies that a + pair of photocells must be installed at- a height of 200 mm and activated to "Close". The photocells consist of a transmitter and a receiver and must be opposite each other. [. . . ] Remedy Green or white cable not wired or badly connected Check terminals precisely. Consider wire lengths Refer to 1x blinking A: Open gate wide enough when programming the travel (50% over maximum) B: Check terminals precisely. Motor 2 has insufficient connection to control board Limits for motor 2 have not been accepted A: After or during programming travel: Wing 1 did not open wide enough and did not meet the integrated passpoint which is located inside the operator halfway above the spindle. B: Motorcables have insufficient connection to contol board Yellow or white cable not wired or badly connected Limits for motor 1 have not been accepted Travel has not been programmed The process of programming has been interrupted Force to operate the gate is too high A: Gate is out of order B: Gate is rough-running C: Gate stopped through windload A: Repair gate B: Check if gate can be easily moved C: Do not operate gate by windstorm D: Reprogram travel to achieve sufficient level of fo Photocells 1 block installation A: Object blocks photocells B: Alignment of the lenses is incorrect C: Power supply to photocells is insufficient Photocells 2 block installation Emergency stop switch blocks installation Safety edge blocks installation A: Object obstructs safety edge B: Defective safety edge C: Power too low or broken wire in supply Power supply to control board is too low A: Defective supply 230V or malfunctioning contact B: Broken wire in supply cable (copper cable) C: The battery (accessory) to operate the gate whilst power failure is dead. [. . . ]