User manual CHAMBERLAIN CPWR

[. . . ] · Activate gate or door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel. · ALWAYS keep gate or garage door in sight until completely closed. NEVER permit anyone to cross path of moving gate or door. SPECIFICATIONS Power: 12VDC, 50 mA Temperature Rating: -40° to +185° F Model CPWR3 RF Frequency: 390 MHZ Accessory Transmitters Visors: CPT1, CPT2, CPT3, CPT4 Key chains: CPTK1, CPTK3, CPTK1PH, CPTK3PH OVERVIEW The Wiegand Receiver (CPWR) is a communication device that transmits an information packet to an access control unit such as a Sentex Telephone Entry System. [. . . ] Refer to the switch settings chart in the Appendix on page 5 for assistance. NOTE: For installations that require the facility code of the transmitters to be passed to the access control system, set the FFC switch to the OFF position (set switch to left). Facility codes are set in the transmitter at the factory to avoid code duplication. 15 14 13 12 11 10 9 8 FACILITY CODE FORMAT 7 6 5 4 3 2 1 0 3 2 1 0 3 2 1 BUTTON FFC Facility code switches 6-15 are not used (must remain in the OFF or left position). Facility Code Factory Setting = All OFF (switches set to left). INSTALLATION AND WIRING 1. (Figure 8) NOTE: Mount receiver with 18" of space above the receiver for the antenna. The receivers should be installed at least 5' apart to avoid "cross-talk". Screw on antenna clockwise and slide rubber boot down to meet o-ring (Figure 7). Connect wires from the CPWR 6-pin connector to the access control system (Figure 8). Refer to the access control system's instructions for appropriate wiring detail. A typical wire connection might resemble the following: CABLE SIGNALS LED DATA 1 DATA 0 +12VDC COMMON (GND) SHIELD WIRE COLOR BROWN WHITE GREEN RED BLACK SHIELD The outside of the antenna connector is not ground. If using an extension kit, do not allow it to contact a metal object. Figure 7 U1 C2 2 Y2 L3 C9 C13 R1 L1 C17 L2 C10 C11 J1 C14 Y1 E1 D11 C9 C23 C20 C18 Y4 C15 C33 C34 C12 C16 R5 C19 R4 U6 R10 C27 L4 R22 Y3 C21 C2 SIGNAL D12 D13 C26 1 C29 DA A T C25 14 U2 R21 C2 R2 R3 R7 R24 R23 A VLID D9 Mounting Holes R6 Q4 R11 CLOCK IN 1 U7 R25 R26 TP4 POWER D1 GRANTED C3 U5 FACILITY 1 C5 CO D E 6 4 2 0 7 5 3 1 TP1 R8 C28 R12 DATA IN FORMAT 3 2 1 0 Q1 3 2 BUTTON 1 C30 C31 14 U3 J3 +5V GND TP3 U12 Mounting Holes NOTE: At power up, the CPWR will perform a system check and produce a series of LED flash sequences (this is normal). 1 15 14 13 12 11 10 9 8 C4 Q2 R19 D7 D6 D5 R20 TP2 C32 FFC D2 U9 14 RP2 1 U4 C7 U10 RP3 1 C8 U8 RP1 1 C6 D8 D3 R17 R16 R14 R13 D3 R15 D16 MADE SENTEX SYSTEMS I N USA R10 D4 J2 To Access Control Circuit Board (Reader Port) Figure 8 3 TESTING AND TROUBLESHOOTING 1. The SIGNAL LED (Figure 9) should be flickering continuously, indicating that the RF receiver circuitry is operating. Press the transmitter button previously set in step 4, page 3, within view of the receiver. If the DATA-yellow and VALID-green LEDs do not light, review the Setting the Switches and Connect Signal/Power Wires sections. NOTE: If the DATA-yellow and VALID-green LEDs flash repeatedly and simultaneously, the format settings may be incorrect (refer to Output Code Format). If reception of the transmitter's signal is significantly reduced, there may be strong RF interference from other sources. [. . . ] This warranty is conditioned upon LiftMaster being paid in full for all equipment; this warranty is not effective until such payment in full has been received. The warranty period shown above applies only to the LiftMaster receiver with Passport technology). Since this is a manufacturer's warranty, not a dealer's warranty, installation, removal, and freight charges are not part of this warranty, nor shall the installer be held liable in any way for removal, repair or installation of the Passport system unless otherwise stated in a separate dealer's warranty. [. . . ]