User manual CHAMBERLAIN 3130 1-3 HP

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual CHAMBERLAIN 3130 1-3 HP. We hope that this CHAMBERLAIN 3130 1-3 HP user guide will be useful to you.


CHAMBERLAIN 3130 1-3 HP : Download the complete user guide (3615 Ko)

Manual abstract: user guide CHAMBERLAIN 3130 1-3 HP

Detailed instructions for use are in the User's Guide.

[. . . ] 845 Larch Avenue Elmhurst, Illinois 60126-1196 www. liftmaster. com ® GARAGE DOOR OPENER Models 3130 1/3 HP For Residential Use Only 3240 1/2 HP Owner's Manual Please read this manual and the enclosed safety materials carefully!The door WILL NOT CLOSE unless the Protector System® is connected and properly aligned. The model number label is located on the front panel of your opener. TABLE OF CONTENTS Introduction 2-5 Adjustment 23-25 Safety symbol and signal word review . . 25 Operation 26-30 Assembly Installation 6 7-22 Fasten rail to the motor unit . [. . . ] The arm should touch the trolley just ahead of the door arm connector hole. Refer to the fully closed trolley/door arm positions in the illustration. Connect the door arm to the trolley: · Close the door and join the curved arm to the connector hole in the trolley with the remaining clevis pin. If the door has a slight "backward" slant in full open position as shown in the illustration, decrease the UP limit until the door is parallel to the floor. NOTE: When setting the up limit on the following page, the door should not have a "backward" slant when fully open as illustrated below. A slight backward slant will cause unnecessary bucking and/or jerking operation as the door is being opened or closed from the fully open position. Figure 5 Inner Trolley Outer Trolley Door Arm Connector Hole Door Arm Emergency Release Handle Closed Door Inner Trolley Outer Trolley Correct Angle Door Arm Connector Hole Open Door Door with Backward Slant (Incorrect) 22 ADJUSTMENT STEP 1 Adjust the UP and DOWN Travel Limits Limit adjustment settings regulate the points at which the door will stop when moving up or down. · Does the door stay closed and not reverse unintentionally when fully closed?If your door passes both of these tests, no limit adjustments are necessary unless the reversing test fails (Adjustment Step 3, page 25). NOTE: Repeated operation of the opener during adjustment procedures may cause the motor to overheat and shut off. If anything interferes with the door's upward travel, it will stop. If anything interferes with the door's downward travel (including binding or unbalanced doors), it will reverse. HOW AND WHEN TO ADJUST THE LIMITS · If the door does not open completely but opens at least 5 feet (1. 5 m): Increase up travel. NOTE: To prevent the trolley from hitting the cover protection bolt, keep a minimum distance of 2-4" (5-10 m) between the trolley and the bolt. · If door does not open at least 5 feet (1. 5 m): Adjust the UP (open) force as explained in Adjustment Step 2. If door still won't close completely and the trolley bumps into the pulley bracket (page 4), try lengthening the door arm (page 21) and decreasing the down limit. · If the opener reverses in fully closed position: Decrease down travel. One turn equals 2" (5 cm) of travel. Limit Adjustment Screws WARNING Without a properly installed safety reversal system, persons (particularly small children) could be SERIOUSLY INJURED or KILLED by a closing garage door. · Incorrect adjustment of garage door travel limits will interfere with proper operation of safety reversal system. · If one control (force or travel limits) is adjusted, the other control may also need adjustment. · After ANY adjustments are made, the safety reversal system MUST be tested. Door MUST reverse on contact with 1-1/2" (3. 8 cm) high object (or 2x4 laid flat) on floor. CAUTION WARNING CAUTION To prevent damage to vehicles, be sure fully open door provides adequate clearance. Left Side Panel ADJUSTMENT LABEL · If the door reverses when closing and there is no visible interference to travel cycle: If the opener lights are flashing, the Safety Reversing Sensors are either not installed, misaligned, or obstructed. If the door is binding or unbalanced, call for a trained door systems technician. [. . . ] Monitors up to 4 garage doors by adding additional sensor modules. 902LM/903LM Garage Door Monitor Sensor: Additional accessory sensor for homes with multiple garage doors. 395LM 377LM Remote Light Control: Enables homeowner to turn on a lamp, television or other appliance from their car with their garage door opener remote or from anywhere in their home with an additional LiftMaster Security® remote. 3088SD 8 Foot (2. 4 m) Complete Rail: To allow an 8 foot (2. 4 m) door to open fully. 35 LIFTMASTER SERVICE IS ON CALL OUR LARGE SERVICE ORGANIZATION SPANS AMERICA INSTALLATION AND SERVICE INFORMATION IS AS NEAR AS YOUR TELEPHONE. SIMPLY DIAL OUR TOLL FREE NUMBER: HOW TO ORDER REPAIR PARTS Selling prices will be furnished on request or parts will be shipped at prevailing prices and you will be billed accordingly. WHEN ORDERING REPAIR PARTS, ALWAYS GIVE THE FOLLOWING INFORMATION: · PART NUMBER · PART NAME · MODEL NUMBER ADDRESS ORDERS TO: THE CHAMBERLAIN GROUP, INC. Country Club Road Tucson, Arizona 85706 SERVICE INFORMATION TOLL FREE NUMBER: 1-800-528-9131 www. liftmaster. com For professional installation, parts and service, contact your local LIFTMASTER/CHAMBERLAIN dealer. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE CHAMBERLAIN 3130 1-3 HP




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual CHAMBERLAIN 3130 1-3 HP will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.