User manual CEPAG STD32

[. . . ] Devices which are made out of modules have to be considered as an industrial product from the safety perspective. During use of the STD32 Short Messages (SMS) can be generated automatically. When using products which are exposed to electric voltage the valid VDE-regulations have to be observed. Especially VDE 0100, VDE 0550/0551, VDE 0700, VDE 0711 and VDE 0860 are applicable. [. . . ] In case of condensation allow a period of acclimatisation of up to 2 hours. Keep away the device from flower vases, bath tubs, washbasins, liquids etc. Do not operate the device in areas where are or could be inflammable gas, vapours or dust. The use of differing spare parts can cause serious material loss or personal injury. The device is designed for the remote switching of devices via the GSM network as well as the remote retrieval of status information of the inputs and the generation of SMS messages after status has changed at the inputs. The STD32 is a telemetry module which is easy to install and simple to use. With the STD32 you can control two relays and monitor the status of two digital inputs with a common mobile phone. Apart from the STD32 you only need a valid SIM Card of any network provider (GSM 900 / 1800 MHz). Typical fields of application are the opening of (garage) doors, switching on and off light and alarm devices as well as generating alarm messages (SMS) or the retrieval of information from door sensors, movement sensors or level sensors etc. As described in picture 1 the STD 32 has four pairs of screw terminals. The other two pairs (Relay1, Relay2) are outputs (switches) of the 2 relays of the STD32. When the engine is booked into the GSM network the GSM LED is flashing once every 2 seconds. In the following chapter "Startup" you will find further information on this. A) Preparation You need an activated SIM card of a GSM network provider. The instructions how to change the PIN are described in the manual of your mobile phone. If you use a SIM card with a PIN different from "0000" in the STD32, the STD32 will use a "wrong" PIN after every restart. In this case you need to use the "Super-PIN" or "PUK" to assign a new PIN to your card. Before connecting the supply voltage to the STD32 please insert the SIM card into the SIM card holder on the backside of the STD32: To open the SIM card holder move it sideward and flip it open; insert the card (mind the orientation) and close it again. As soon as this is done, the GSM LED will be flashing once every 2 seconds. Now take the mobile phone with which you want to control the STD32 and call the phone number of the SIM card which is inside the STD32. From now on the STD32 can only be operated by this mobile phone(or this SIM card in another phone). If you want to use another mobile phone with a different phone number with your STD32 you have to set it back to the factory settings before you can make a new configuration call (see chapter "configuration SMS"). [. . . ] F) Table of SMS Commands Factory settings Status of I/Os Start SMS on/off Relais 1 on Relais 1 off Relais 2 on Relais 2 off Switching time Relais 1 Switching time Relais 2 Delay before reply (Relais 1) Delay before reply (Relais 2) Time of activation Input 1 Time of activation Input 2 Invert Input 1 Invert Input 2 A) Switching by phone call After successful configuration (see chapter "Startup") please call the phone number of the SIM card which is inside the STD32. Take care that your mobile phone is transmitting the phone number (to check that you can call another mobile phone; your phone number or name must be visible on the display then) Now the relay should switch for a certain time according to the configuration. C) Send SMS Commands To protect your STD32 against unauthorized use every SMS has to start with the last 4 digits of the IMEI number. La destination de l'appareil est de permettre la mise en route et l'arrêt à distance d'appareils via le réseau GSM, ainsi que l'interrogation à distance des entrées et l'émission de SMS suite à une modification des entrées. [. . . ]