User manual CATERPILLAR PM-200 BROCHURE

[. . . ] PM-200 Cold Planer Cat® C18 Engine with ACERT® Technology Gross Power (SAE J1995) 429 kW 30 900 kg Operating Weight Rotor Width 2010 mm Rotor Depth (maximum) 320 mm 575 hp 68, 135 lb 79" 12. 6" PM-200 Cold Planer The new PM-200 combines enhanced production capabilities, optimized performance and simplified service to complete tough milling applications with productive results. C18 Engine with ACERT® Technology ACERT® Technology works at the point of combustion to optimize engine performance and provide low exhaust emissions. The C18 engine with ACERT® Technology provides clean burning power. Page 4 Propel System Propel pump provides balanced flow to dual displacement drive motors on each track. The electronically controlled load sensing system matches propel speed to load on engine for maximum production. [. . . ] Sensor measures side plate movement that enables the entire length of the side plate to become an averaging device for extremely accurate grade matching. Allows manual or automatic operation from either the operator's station or at ground level. Constant read-out for rotor depth and cross slope are easily visible in direct sunlight or low light conditions. Quick-connect feature simplifies system diagnostics. Ecology drains. They are included on the radiator, engine oil pan, hydraulic and fuel tank. Scheduled Oil Sample ports allow for simple fluid collection of hydraulic oil. Polyethylene routing blocks provide a secure routing to reduce rubbing and increase service life of hoses. Batteries are specifically designed for maximum cranking power and protection against vibration. The cooling package is a single plane design, stacked in series for easy access for cleaning and service. A modular stacked cooling system provides more efficient cooling of individual systems and makes routine cleaning easier. In an engine not running condition or non-operational auxiliary hydraulic system, full operational control of main machine functions are readily available for assisted machine movement for maintenance and servicing. The power-assist engine hood opens wide to provide excellent access to the engine, air filter, hydraulic components and daily service points. 9 Engine The Caterpillar® C18 engine with ACERT® Technology is a six cylinder, turbocharged air-to-air after-cooled diesel engine. Engine Gross Power SAE J1995 Net Power ISO 9249 EEC 80/1269 SAE J1349 Specifications Bore Stroke Displacement I Propel System Hydrostatic drive with hydraulic flow provided by a variable displacement piston-type pump. Drive motors with planetary gear reduction on each track provides balanced tractive effort. Features I Rotor Drive System Operates direct through a hydraulically actuated, Caterpillar wet clutch driving a planetary gear reducer. Features I Cat® C18 kW hp 429 575 kW hp 415 557 415 557 410 550 145 mm 5. 7" 183 mm 7. 2" 18. 1 liters 1105 in3 I I I I I The power ratings apply at a rated speed of 1900 RPM when tested under the reference conditions for the specific standard. The net power advertised is the power available at the flywheel when the engine is equipped with an alternator, air cleaner, muffler and fan at minimum speed. Dual fuel filters with water separator and air compressor are standard. I I I I A variable displacement, piston-type pump with electronic displacement control supplies pressurized flow. Positive traction control valve provides equal hydraulic oil flow to each drive motor to increase tractive effort in hard or deep cuts. Drive motors have two swashplate positions allowing operation at either maximum torque throughout the entire milling speed range or at a faster travel speed for moving around the job site. Gear selection controlled electrically by a two-position switch on the operator's console. Infinitely variable machine speed and direction of travel controlled by propel lever. Load control system, controlled by Electronic Control Module (ECM), matches propel speed to load on the engine for maximum production. With the machine in work mode and load control engaged, three load control settings can be selected. Tracks are 1640 mm (64. 5") long, 300 mm (12") wide and feature replaceable polyurethane track pads for long service life. I I I I I Heavy-duty wet clutch mounts directly to the engine. [. . . ] Sonic grade control sensors can be positioned on each side are easy to position and provides a consistent accuracy. Wire rope contacting grade sensor measures side plate movement that enables the entire length of the side plate to become a mini averaging ski for optimum grade matching. Sonic Averaging System features three non-contacting grade sensors or a combination of one contacting and two non-contacting sensors that mount on the side of the machine. Enables the entire length of the machine to become an averaging device. [. . . ]