User manual CATERPILLAR 637G BROCHURE

[. . . ] 631G/637G Wheel Tractor Scrapers ® Engine Tractor Engine Net Power Scraper Engine Net Power Cat C18 ACERTTM 345/373 kW 462/500 hp Cat C9 ACERT 198/211 kW 266/283 hp ® Scraper Bowl Heaped Capacity Rated Load 26 m3 37 285 kg 34 yd3 82, 200 lb 631G/637G Wheel Tractor Scrapers Power Train ­ Engine The C18 and C9 engines with ACERTTM Technology work at the point of combustion to optimize engine performance and minimize exhaust emissions. Matched with the torque converter and power shift transmission, they provide years of dependable and efficient service. 4 Power Train ­ Transmission Electronic controls switch from converter drive to direct drive based on gear selection, maximizing efficiency and power application. Tractor and scraper engines are synchronized for smooth operation and longer service life. [. . . ] Releasing the yellow button sets the top gear. Joystick Control: positions, switches and buttons Grab Handle/Hand Rest. The grab handle/hand rest located next to the joystick controller helps operators when adjusting seat swivel, and gives them a place to rest their hand while on the haul and return roads. Simple and easy to operate, the joystick enhances the productivity of operators of all skill levels. Requires less force to control the critical scraper functions and requires less lever travel. 1) Bowl (forward and back) 2) Ejector (side to side) 3) Apron (thumb rocker switch) 4) Transmission Hold 5) Cushion Hitch 6) Rocker switch (not shown ­ is on front of joystick) · · Auger (on/off) Push-Pull (bail up/down) * Standard open bowl does not have a rocker switch. 9 Electronic Controls Integrated electronic controls provide smooth, consistent shifts through the synchronization of engine and transmission speeds. Low Battery Elevated Idle. The ADEM A4 controller automatically compensates for low alternator output at low idle by raising the rpm for brief intervals to keep the batteries fully charged. Combined monitoring systems, easy access diagnostics and more durable components make routine maintenance and servicing simple and fast. The Electronic Monitoring System (EMS III) is designed to monitor both the tractor and scraper from one location instead of two. Both the tractor and powered scraper use the same controller for parts commonality and easier servicing. A variety of diagnostic codes are accessible through the EMS main display module, via the Electronic Technician (Cat ET). This offers a head start on problem solving, so with a radio call the service technician can know which tools, troubleshooting guides, and possibly even replacement parts to bring to the machine. The EUI system has fewer moving parts than mechanical unit injection and requires few adjustments. The ADEM A4 controller communicates with the monitoring system (EMS) to warn the operator when problems arise, to help avoid major damage. EUI engines have virtually no mechanically controlled parts to wear or adjust. These have been replaced by electronic controls, reducing maintenance costs and increasing machine availability. Product Link is a wireless system that allows the customer to track machine data such as location, service meter hours as well as machine health information. The system can automatically issue alerts when the machine is operated beyond ownerdefined time and location limits. Product Link is available as a factory attachment or it may be installed in the field in that there is a mounting location for the module as well as an antenna on the machine. A wiring breakout is standard, eliminating the need to splice into existing wires. Electronic controls optimize the timing setting for varying conditions. The ADEM A4 controller matches timing to the load on the engine, engine rpm and temperature. The ADEM A4 controller monitors electronic sensors to determine the optimum fuel/air ratio. Fuel is precisely controlled during cranking, starting and acceleration to reduce smoke. [. . . ] Diagnostic programs such as S·O·SSM Analysis and Coolant Sampling and Technical Analysis help avoid unscheduled repairs. Your Cat dealer can help you evaluate the cost involved so you can make the right choice. 15 Engine Tractor Engine Scraper Engine Cat C18 ACERTTM Cat C9 ACERT Scraper Bowl Heaped Capacity Rated Load Struck Capacity Depth of Cut ­ max. Apron Opening Apron Closure Force 26 m3 37 285 kg 18. 3 m3 437 mm 3512 mm 545 mm 28 mm 255 kN 360 kN 480 mm 2007 mm 170 kN 34 yd3 82, 200 lb 24 yd3 17. 2 in 138. 3 in 21. 5 in 1. 12 in. 57, 375 lb 81, 000 lb 18. 9 in 79 in 38, 250 lb Tractor Engine Net Power Gross Power ­ Gears 1-2 Gross Power ­ Gears 3-8 Net Power ­ Gears 1-2 Net Power ­ Gears 3-8 Bore Stroke Displacement 345/373 kW 364 kW 392 kW 345 kW 373 kW 145 mm 183 mm 18. 1 L 462/500 hp 488 hp 526 hp 462 hp 500 hp 5. 7 in 7. 2 in 1, 105 in3 · Net power advertised is the power available at rated speed of 1, 800 rpm, measured at flywheel when the engine is equipped with fan, air cleaner, muffler and alternator. [. . . ]