User manual CAT EYE ST250 (ENDURO)

[. . . ] 3 years(The life of the first factory-loaded battery may be shorter than this period. ) Dimension/Weight ------------------------ 1-15/16" x 1-25/32" x 5/8" (49 x 45 x 16 mm) / 0. 74 oz (21 g) * The specifications and design are subject to change without notice. LIMITED WARRANTY 1-Year Warranty for Main Unit Only (Accessories/Attachments and Battery Consumption excluded) If trouble occurs during normal use, the part of the Main Unit will be repaired or replaced free of charge. To return the product, pack it carefully and remember to enclose the warranty certificate with instruction for repair. Please write or type your name and address clearly on the warranty certificate. Insurance, handling and transportation charges to our service shall be borne by person desiring service. 1. [. . . ] To remove, pull it Fig. 6 magnet off forward while pushing down the lever. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japan Attn. : CAT EYE Customer Service Section Service & Research Address for United States Consumers: CAT EYE Service & Research Center 1705 14th St. 115 Boulder, CO 80302 Phone : 303-443-4595 Toll Free: 800-5CATEYE Fax : 303-473-0006 e-mail: CatEyeUSA@aol. com #169-9731 Heavy Duty Wire and Bracket Sensor Kit #169-9771 Bracket Sensor Kit for Extra Large Fork #169-6168 Bracket Sensor Kit for Aero Bar #169-6167 Center Mount Bracket Kit #169-6169 Stem Mount Bracket Kit nyron ties wire Fig. 7 ·Test Mount main unit. If main display does not show any figures, press either M button or S/S button to release from power saving function. If not, adjust relative positions of magnet and sensor following the instructions. #169-9750 Attachment Kit (For Heavy Duty Wire) #169-9751 Attachment Kit (For TOMO XC) #166-5120 lever #169-6180 Lithium Battery(CR1620) Wheel Magnet bracket Fig. 9 Fig. 8 rubber pad Slide the main unit onto the bracket from front until it clicks into position. (Fig. 9) MEASURING AND DISPLAY FUNCTIONS OPERATING INSTRUCTIONS DST SPD Current Speed 0. 0(3. 0) - 65 mile/h(27inch) ±1 mile/h under31 miles/h This is always displayed on the main display and updated once a second. TOMO XC A. K. Main Display (Speed) Sensor Pulse Symbol Mode Symbol Speed Scale Symbol Auto Mode Symbol Sub-Display (Selected Function) M (Mode) Button S/S (Start/Stop) Button Set Button Battery Case Cover Contact ODO Total Distance (Odometer) ODO 0. 0 - 9999. 9 mile ±0. 1 mile This is continuously measured until battery wears down or all clear operation is done. DST Trip Distance 0. 00 - 999. 99 mile ±0. 01 mile DST The trip distance from start to current point is displayed. TM Elapsed Time 0:00'00" - 9:59'59" ±0. 003 % BUTTON FUNCTION MXS ODO DST TM AVS · M button (Fig. 1) Changes the display in the order shown in fig. · S/S button Starts and stops the measurement of trip distance and elapsed time. In Auto Function, this button is invalid. Fig. 1 TM Elapsed time is measured from start to current point, in units of hours, minutes and seconds. AVS Average Speed 0. 0 - 65. 0mile/h ±0. 3 mile/h AVS The average speed from start to current point is displayed within 27 hours 46 minutes 39 seconds (99, 999 seconds) or 999. 99 miles (km). MXS Maximum Speed 0. 0(3. 0) - 65 mile/h(27inch) ±1 mile/h MXS · SET Button This is for setting the wheel circumference and clock time, switching on/off Auto Function and to clear all present data and any irregularity. When pressed in stop state in each mode, the following can be revised. · In ODO mode ------------------ Wheel circumference · In mode -------------------- 12-hour clock · In TM, DST or AVS mode --- On/off the Auto function Reset Operation: (Fig. 2) Select any mode except ODO, then press M button and S/S button simultaneously. (When done in ODO, registered wheel circumference will be displayed. ) All Clear Operation: (Fig. 3) When M button, S/S and set buttons are pressed simultaneously, all data stored (ODO, speed scale, Wheel circumference and clock time) is erased. This should only be executed after replacing battery or when irregular display occurs due to static electricity, etc. Since all memories are erased, set necessary data again according to "Main Unit Preparation". With Reset operation, it returns to zero and counting begins anew. 12-hour clock time The current time is displayed by a 12-hour clock. 0:00' - 11:59' ±0. 003 % AUTO (AUTOMATIC START/STOP) FUNCTION DST AUTO Reset Operation Fig. 2 All Clear Operation Fig. 3 This function switches the main unit to start or stop automatically, in which AUTO symbol appears on the screen, and you are free from pressing S/S button each time. In TM, DST or AVS, this function switches on/off with each press of SET button. * 2 seconds may be elapsed if mount the main unit to the bracket with this function on. POWER SAVING FUNCTION When main unit is left without receiving any signal for 60-70 minutes continuously, power supply is shut down and main unit will display ( ) only as the figure. [. . . ] ----- Is there anything on the contact of the main unit or of the bracket?----- Are the marking line of the sensor and the center of magnet matched each other?----- Refer to "Sensor/Magnet Mounting" and re-adjust correctly. ----- Water or condensation may collect between the bracket sensor and the computer causing an interruption in the data transmission. [. . . ]