User manual CAT EYE CC-CL200 (CORDLESS 2)

[. . . ] et le produit à réparer doit être retourné à CAT EYE Co. , Ltd. Tout produit retourné au service de réparation CAT EYE doit être soigneusement emballé et le certificat de garantie ainsi que les instructions de réparation doivent accompagner le produit à réparer. Il est conseillé à l'acheteur d'écrire lisiblement ou de dactylographier ses nom et adresse sur le certificat de garantie, afin que le produit puisse lui être directement retourné dès que les réparations/réglages nécessaires sont terminés. Le coût de l'assurance ainsi que les frais de manutention et de transport vers le service de réparation CAT EYE sont à charge de la personne souhaitant une réparation sous garantie. #169-6690 Parts Kit Kit d'accessoires Ersatzteil Onderdelen set Kit d'accessori Kit de piezas Adresse d'envoi pour réparation CO. , LTD. 2-8-25, Kuwazu, Higashi Sumiyoshi-ku, Osaka 546-0041 Japon. [. . . ] For best performance, the triangle mark on the sensor shall aim at the direction to the main unit. The distance between the sensor and main unit must be kept within 45 cm. The signal reception range may shorten as a result of low ambient temperature or lowered battery power. The battery service hours quoted above is the average for a 45cm distance between the sensor and main unit. · The cordless system may be interfered with in the following situation, so that main unit may display false data. Riding in places where intensive electromagnetic wave or field exist, such as TV transmission station and radar installations. When two bicycles carrying similar cyclocomputers are ridden side by side. Whenever this button is pressed, the mode display changes in the order shown in fig. 1, and the data is displayed on the sub-display. Open the battery cover on the back and insert a new CR2032 (lithium) with the (+) pole upward, while pressing the side of the battery against the contact. Mount the sensor back to the bicycle and adjust to relative position, clearance and direction. MAIN UNIT PREPARATION B AT User must make the following setting according to instructions before the cyclocomputer can be used properly. Fig. 7 1. How to measure the exact Wheel Circumference (L)(Fig. 3) First, adjust tire pressure and then put a mark on the tire tread and the ground simultaneously. Mark the ground at the end of one revolution and then measure the distance between the two marks. Or, the "Setting Values Cross Reference Table" can help you to find out an approximate wheel circumference according to tire size. bracket Fig. 21 contact DISPLAY FUNCTIONS S A Fig. 8 Current Speed 0. 0(3. 0) to 65. 9 miles/hr ±0. 3mile/h This is always displayed on the main display and updated once a second. D 2. Setting the Speed Scale (Fig. 4) When the AC button is pressed and all displays illuminate then the "mile/h" appears as shown in fig. 4. "km/h" and "mile/h" are displayed alternatively each time the right button is pressed. Select any speed scale as desired and press SET button to complete the setting. A O 0. 0 to 99, 999 miles ±0. 1mile This is continuously measured until battery wears down or all clear operation is done. At 10, 000 miles(km), it returns to zero and counting begins anew. O Total Distance Fig. 9 lever bracket rubber pad 3. Setting the Wheel Circumference (Fig. 5. 6) A D Trip Distance D Fig. 10 This cyclocomputer is able to memorize two different wheel circumferences. One main unit can be used on two bicycles subject to buy another set of slide bracket and sensor. Two wheel circumferences, (A) 2155mm and (B) 2030mm, have been set befront fore the cyclocomputer left our factory. The (A) wheel circumference 2155mm (standard for 27 inch tire) will blink as shown in fig. 5. If you want to change, press either the right button to increase or left button to decrease the number. If you want to set a second circumferfront fork ence, press the left and right buttons together before pressing the SET button. [. . . ] Figures do not appear on the main display ------------- Cancel the power saving function. Speed is not displayed when riding with high speed or at low temperature. --------------------------------------------------------------------- Check the sensor position and direction. --------------------------------------------------------------------- Has the battery worn out? [. . . ]