User manual CAT EYE ABS25

[. . . ] Before first use, charge the battery fully following the instructions on [RECHARGING INSTRUCTIONS]. CONTENTS The ABS series are the combined system of the following parts. Make sure that your package includes all the parts that are necessary for your model. Model ABS-20 ABS-25 ABS-30 ABS-35 Spot 10W 15W 20W 20W Lamp Unit Wide Body Material 10W Plastic 10W Aluminum 10W Aluminum 15W Aluminum Battery Pack (battery type) Ni-Cd 6V 1600mAhx2 Ni-MH 6V 2200mAhx2 Hi Ni-MH 6V 3000mAhx2 Hi Ni-MH 6V 3000mAhx2 Battery Charger (exclusive for each battery type) Ni-Cd (normal) CHR-1610 Ni-MH (normal) CHR-2210 Hi Ni-MH (normal) CHR-3010 Hi Ni-MH (fast) QCHR-3010 Battery Charger 6v 6v Copyright© 2002 CAT EYE Co. , Ltd. ABS-021107 066640037 2 SAFE OPERATIONS (IMPORTANT) · Never short-circuit the terminal of the battery pack and the plug of the battery charger. [. . . ] · If the lamp body or parts become dirty with mud, etc. , clean with a soft cloth which is moistened with mild soap. Never apply paint thinner, benzine or alcohol; damage will result. Rubber Pad Battery Belt (Lx2/Sx2) Cable Cover Holder Mounting Bolts Joint Cord Holder Switch Unit CLICK! HOW TO ATTACH Attach the brackets (H-32 x 2 pieces) to the handlebar. How to distinguish the spot bulb from the wide bulb: the inside reflective mirror of the spot bulb is more finely cut. Attach the switch unit onto the handlebar where it will not hinder the braking and shifting operation. To remove the switch unit, slide it to the left while pushing the lever. · Recharge after thorough discharge. (in order to prevent memory after effect) · Recharge two batteries simultaneously · Use exclusive charger Standard Charging Time ABS20/25/30: 8 -10 hours ABS35 (fast charge): 3 hours The home power outlet CLICK! or CLICK! Lever RECHARGING INSTRUCTIONS · Recharge only when battery power has completely diminished. · Fully charged batteries that yields no power means battery life is dead. Bracket (H-32) Switch Unit Rubber Pad Quick lever screw Lever Rubber Pad Screw Charge indicator · Do not mix different types of batteries Choose your favorite location to attach the battery packs. When attaching to bottle cage Even if they are the same type, never Attach the holder onto the down tube using the holder mounting bolts. mix them if they are in different 1 Fit inside Holder states of charge. For safety's sake, also use the battery belts (velcro straps) to secure the batteries. · Do not mix batteries that are in different states of charge Connecting Battery Pack and Cord ABS20 (Plastic body) Only 10W bulb is applicable. HOW TO REPLACE THE BULB Disassemble the lamp unit as illustrated. Bulb Holder Holder Mounting Bolt 2 ABS25/30/35 (Aluminum body) All bulbs are applicable. Strap Battery Pack Wind straps When attaching to frame Fix the battery pack firmly to the frame, using the battery belts. How to run the battery Battery Pack belt through the slot Velcro Frame Ring Battery Belt Battery pack Top Tube Battery Pack Jack Bulb Cable Cover Connecting Cord Switch Unit Note: If the cable is not covered by cable housing, use the included cable cover to prevent direct contact between the cable and the belts. In this case, the run time becomes half of the designated time. Caution: · Do not rotate the bulb but pull it straight out. · Never use (2) 20w bulbs at the same time. SAFETY SYSTEM (AUTO-RESET FUSE) When an electrical surge or malfunction occurs in the circuit or the temperature of the battery rises, the fuse blows due to its safety system and the circuit will be closed. Note: If the fuse continues to blow, or if the fuse does not recover, call the appropriate service center for assistance. SPECIFICATIONS 6V Halogen spot bulb + wide bulb (ABS-20: 10W+10W/ABS-25: 15W+10W/ABS30: 20W+10W/ABS-35: 20W+15W) Battery pack: ABS-20: Ni-Cd battery Ni-Cd/6V 1600mAh ABS-25: Ni-MH battery Ni-MH/6V 2200mAh ABS-30/35: Hi Ni-MH battery Hi Ni-MH/6V 3000mAh Battery charger: ABS-20: Ni-cd charger (normal) CHR-1610 ABS-25: Ni-MH charger (normal) CHR-2210 ABS-30: Hi Ni-MH charger (normal) CHR-3010 ABS-35: Hi Ni-MH charger (fast) QCHR-3010 * As for Hi Ni-MH charger, normal charger and fast charger is compatible with each other. [. . . ] Type your name, address, date of purchase and the situation of trouble clearly on the warranty certificate, and send it back to the appropriate service center together with the product. Insurance, handling and transportation charges shall be borne by the customer. After being repaired or replaced, the product will be shipped back to the customer. Pad HOW TO SWITCH ON/OFF Run Time Model Spot Beam Wide Beam Spot + Wide 0. 8 hr 1. 0 hr 1. 0 hr 0. 9 hr ABS-20 1. 6 hrs(10W) 1. 6 hrs(10W) ABS-25 1. 6 hrs(15W) 2. 4 hrs(10W) ABS-30 1. 5 hrs(20W) 3. 0 hrs(10W) ABS-35 1. 5 hrs(20W) 2. 0 hrs(15W) The switch unit controls the operation of the lamps. [. . . ]