User manual CASIO 3796

[. . . ] MA0508-EA Operation Guide 3796 Getting Acquainted Congratulations upon your selection of this CASIO watch. To get the most out of your purchase, be sure to read this manual carefully and keep it on hand for later reference when necessary. Warning! · The longitude, lunitidal interval, Moon phase indicator and tide graph data that appear on the display of this watch are not intended for navigation purposes. Always use proper instruments and resources to obtain data for navigation purposes. · This watch is not an instrument for calculating low tide and high tide times. [. . . ] · You can also select auto-repeat, which automatically restarts the countdown from the original value you set whenever zero is reached. · All of the operations is this section are performed in the Countdown Timer Mode, which you can enter using C. Timekeeping Mode time Moon/Tide Data Tide graph Time Year Month ­ Day Moon phase indicator Tide Data Screen Moon/tide data lets you view the Moon age and Moon phase for a particular date, and tidal movements for a particular date and time at your Home Site. · If you suspect that the current Moon/tide data is wrong for some reason, check the current Timekeeping Mode settings (time, date, and Home Site), and correct them if required. · See "Moon Phase Indicator" for information about the Moon phase indicator and "Tide Graph" for information about the tide graph. · All of the operations in this section are performed in the Moon/Tide Data Mode, which you enter by pressing C. To use the countdown timer Press D while in the Countdown Timer Mode to start the countdown timer. · When the end of the countdown is reached and auto-repeat is turned off, the alarm sounds for 10 seconds or until you stop it by pressing any button. The countdown time is automatically reset to its starting value after the alarm stops. · When auto-repeat is turned on, the countdown will restart automatically without pausing when it reaches zero. · The countdown timer measurement operation continues even if you exit the Countdown Timer Mode. · Press D while a countdown operation is in progress to pause it. · To completely stop a countdown operation, first pause it (by pressing D), and then press A. While the countdown start time is on the display in the Countdown Timer Mode, hold down A until the hour setting of the countdown start time starts to flash, which indicates the setting screen. · If the countdown start time is not displayed, use the procedure under "To use the countdown timer" to display it. Press C to move the flashing in the sequence shown below to select other settings. Hours Minutes Auto-repeat To view the current Moon/Tide Data Mode data In the Moon/Tide Data Mode, press A to toggle between the tide data screen and the Moon data screen. · The tide graph shows the tide for the currently displayed time. The Moon data screen shows the Moon age and Moon phase for the current date. Tide Data Screen Time 3. · All of the operations in this section are performed in the Alarm Mode, which you enter by pressing C. The Dual Time Mode lets you keep track of time in a different time zone. You can select Standard Time or Daylight Saving Time for the Dual Time Mode time. · In the Dual Time Mode, the seconds count is synchronized with the seconds count of the current digital time. To set the Dual Time DST indicator Dual time (Hour : Minutes) Alarm date (Month ­ Day) 1. In the Dual Time Mode, hold down A until the DST setting starts to flash, which indicates the setting screen. Press C to move the flashing in the sequence shown below to select the other setttings. DST Hour Minutes Alarm Types The alarm type is determined by the settings you make, as described below. [. . . ] Since this watch performs calculations using integer values only (no fractions), the margin for error of the displayed Moon age is ±1 day. Hourly time signal on indicator To select the operation of Alarm1 1. Press A to cycle through the available settings in the sequence shown below. Alarm on Snooze alarm on Alarm off · The applicable alarm on indicator (SNZ ALM) is displayed in all modes when an alarm is turned on. · SNZ indicator flashes during the 5-minute intervals between alarms. · Displaying the Alarm1 setting screen while the snooze alarm is turned on automatically turns off the snooze alarm (making Alarm1 a one-time alarm). 3 Operation Guide 3796 Tide Graph The tide graph uses arrows like those shown below to indicate the tide at the currently displayed time. [. . . ]