User manual CARDO SCALA RIDER Q2

[. . . ] TM Q2 TM communication in motion TM User Guide Gebrauchsanleitung Guide d'Utilisation Guida di Avvio Guia de Usario © Cardo Systems, Inc. The Bluetooth® word mark and logos are owned by the Bluetooth SIG, Inc. Other trademarks and trade names are those of their respective owners. 2 scala rider® Q2TM INTRODUCTION Congratulations, and thank you for choosing the scala rider Q2 Bluetooth® Headset for bikers. This Manual will help you operate the headset, but you should first familiarize yourself with the Bluetooth functionality of your cellular phone and/or GPS device before using the scala rider Q2. [. . . ] AUDIO SOURCES AND PRIORITIES The different Audio Sources that are connected to the scala rider Q2 are prioritized as follows: Highest 1. Mobile phone Audio / GPS device (Incoming/outgoing calls , GPS audio and navigation instructions) 2. MP3 Connectivity NOTE: When using a scala rider Headset (not a Q2 version) as a Passenger headset, Voice Connect Intercom can be initiated only by the scala rider Q2 headset. Failed Connection: On the scala rider Q2, if you attempt to start a Buddy Intercom call with a Buddy that is already on a Phone/GPS/ Intercom call, you will hear a double beep indicating the Buddy is busy. scala rider® Q2TM 9 Reconnecting the Intercom: If the scala rider Q2 and its Intercom Buddy headset go out of range and disconnect from each other, the scala rider Q2 will automatically try to reconnect to its Intercom Buddy for five minutes. You can manually reconnect at any time by pressing the MC Button (single tap for Primary Buddy and double tap for Secondary Buddy). Receiving Intercom calls If you are not speaking with any one, once the other party tries to initiate a Buddy Intercom call, the call will begin immediately. TROUBLESHOOTING THE INTERCOM: First, make sure your microphone is located properly in front of the center of your mouth. Please make sure to test the Intercom functionality in a LOUD environment, such as next to an idling motorcycle. Please also verify that the headsets were paired together properly by following the instructions in the relevant Setup sections. · One beep ­ Voice Connect set to Primary Buddy · Two beeps ­ Voice Connect set to Secondary Buddy Enable/Disable Voice Connect feature Press and hold the Volume Up and Down Buttons simultaneously until you hear a beep. NOTE: The Enable/Disable Voice Connect feature affects the Intercom functionality only. MAKING AND RECEIVING MOBILE PHONE CALLS PHONE FUNCTIONS Answer a call Reject a call Terminate a call Voice Dial Short press the CTRL Button or speak loudly any word of your choice during an incoming call. Short press the MC Button or remain silent for 15 seconds during an incoming call. During Standby, short press the CTRL Button and state the name of the person you wish to call. This feature is supported only by mobile phones that support the Voice Dial feature. Press and hold the Volume Down Button for three seconds during Standby. Setting Voice Connect Intercom preference (Primary vs. Secondary Buddy) The headset's Voice Connect feature allows you to start a Buddy Intercom call by simply speaking into the microphone. You can define which of the two Buddy headsets you wish to connect to when using Voice Connect Intercom. To toggle the Voice Connect Intercom between Primary and Secondary Buddy: Press and hold the Volume Up Button for three seconds and you will hear a beep: 10 scala rider® Q2TM Redial NOTE: If your Bluetooth mobile phone is paired to a Bluetooth GPS device, not directly to the scala rider Q2, some of the above Phone functions may not be compatible. When the headset is on an active phone call, any Buddy Intercom call request will be rejected automatically. Once the phone call audio link drops, you can initiate and accept Buddy Intercom calls. STATUS LIGHT STATES None Alternating Red/blue flashes Rapid Red flashes 1 blue flash every 3 seconds Headset is off Mobile phone/GPS Pairing mode Intercom Pairing mode Standby ­ No call is in progress call), press and hold the MC Button on your headset for three seconds to turn on the radio. With some phones you should wait a few seconds after ending a call before turning on the Radio. Turning the FM Radio Off While the radio is turned on, press and hold the MC button for three seconds to turn the Radio off. Switching Preset FM Radio Station There are six pre-set Radio stations available on your scala rider Q2. While the Radio is on, tap the MC Button to cycle between saved stations. [. . . ] Declaration of Conformity (DOC) The scala rider Q2TM headset is compliant with and adopts the Bluetooth® Specification 2. 0 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed. English By using the scala rider Q2 you will waive substantial legal rights including the right to sue. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. By using the headset you agree to be bound to this agreement and forfeit the right to sue. [. . . ]