User manual CARDO SCALA RIDER G4

[. . . ] CONNECTING BLUETOOTH ENABLED MOBILE PHONES, GPS OR MP3 (A2DP) DEVICES . THE SOUND OF MUSIC: Built-In FM Radio and external MP3 Player (cable option) . 11 7. 2 CABLE CONNECTING YOUR MP3 PLAYER OR OTHER EXTERNAL AUDIO SOURCES . Please note, that our manual is updated periodically on the Cardo website in order to include the very latest features as well the new options and functions of your new scala rider G4 headset. [. . . ] For details, visit www. cardosystems. com/other-products/src. English Solid red 9. USING THE INTERCOM 9. 1 INTRODUCTION The scala rider G4 provides you with an impressive Bike-to-Bike Intercom range by simply flipping up the antenna. The Flip-up antenna allows you to maximize intercom range with other bikers at up to 1 mile / 1. 6 km (subject to terrain). The antenna is also Flip-up Antenna for extended range useful when riding in dense urban environments that may affect the transmission quality. You may keep the Flip-up Antenna open when not using the intercom, even though there is no particular need to do so. To set up one or two Intercom Bluetooth connections, you must first pair your G4 headset with the other headsets. In this manual such other headsets will be referred to as CHANNEL "A" and CHANNEL "B" respectively. scala rider® G4TM 13 9. 3 BEFORE STARTING THE INTERCOM Your scala rider G4 headset has two buttons designated for quick connection to two other headsets. These other headsets are referred to as CHANNEL "A" and CHANNEL "B". In the following sections you will also learn how to add a third participant and conduct an intercom conference mode. Select your preferred Pairing Option HEADSETS TO BE PAIRED Your G4 with another G4 Your G4 with a Q2 Your G4 with one earlier scala rider model Your G4 with two other G4 units Your G4 with one G4 and one Q2 unit Your G4 with two Q2 units GO TO SECTION 9. 10 a 9. 11 a 9. 11 b 9. 10 b 9. 11 c 9. 11 c 9. 11 c 9. 11 c 9. 11 c 9. 10 c Channel "A" Button Channel "B" Button Your G4 with one G4 and one other scala rider model Your G4 with one Q2 and one other scala rider model Since the scala rider G4 can be paired with all models among the scala rider family, we recommend that you first pair it according to your preferred configuration and then change or modify as often as you wish later as the need arises. For example: If you typically use the intercom to communicate with two friends who both use G4 units, then you should pair it as described below in section 9. 10 b. Therefore, please select your initial pairing preference now amongst the following options in the table below and following that, refer to the pairing procedure as described in the respective section of this manual. When done, return to the explanations in section 9. 4 "Initiate Intercom Calls". 14 scala rider® G4TM Your G4 with two other scala rider models Your G4 as part of 4-Way intercom call configuration 9. 4 INITIATE INTERCOM CALLS Now that you have completed the pairing process, you can start using the intercom. If you haven't done so yet, please refer to the table above and complete your preferred pairing configuration before you proceed with this section. There are two ways to start an Intercom call with headsets that are paired to your scala rider G4 (make sure you are in Standby mode): VOICE CONNECT: Preferred for relatively brief conversations as it takes the channel into standby mode after 30 seconds of silence Start talking loudly Once you start talking loudly, an Intercom call will be established with both paired headsets, CHANNEL "A" and CHANNEL "B" (if both are available). The Intercom call will stay on until all participants remain silent for 30 seconds. (applicable for 2-way communication) CHANNEL BUTTON CONNECT: Preferred for extended conversations as it leaves the channel open and active Single tap the CHANNEL "A" Button to add or remove the CHANNEL "A" headset from an Intercom call. Single tap the CHANNEL "B" Button to add or remove the CHANNEL "B" headset from an intercom call. 9. 6 ENABLE/DISABLE VOICE CONNECT FEATURE (VOX) The G4 offers VOX technology for safe and hands-free operation of some key functions. To reject an incoming call, you need only to remain silent for about 15 seconds. While on standby press and hold the Volume Up and Volume Down Buttons simultaneously for three seconds until you hear a beep. The default status is Voice Connect enabled. NOTE: The Enable/Disable Voice Connect feature affects only the Intercom functionality. English NOTE: While the Intercom is on, the Redial and Voice Dial functions will be disabled. 9. 7 RESET PAIRING (RESTORING THE ORIGINAL DEFAULT CONFIGURATION) This section is only relevant once you have completed a pairing process You can delete all of your paired devices at any time as follows: 1. With the scala rider G4 headset turned ON, press and hold the Mobile Button for at least six seconds until the Red and Blue Lights begin rapidly alternating. The Red and Blue Lights will flash five times simultaneously and then the headset will turn off, confirming that Reset was successfully completed. [. . . ] The Product is manufactured in accordance with Annex II of the above directive. Declaration of Conformity (DOC) The scala rider G4 headset is compliant with and adopts the Bluetooth® Specification 2. 1 and has successfully passed all interoperability tests that are specified in the Bluetooth® specification. However, interoperability between the device and other Bluetooth®-enabled products is not guaranteed. WAIVER AND GENERAL RELEASE By using the scala rider G4 you will waive substantial legal rights including the right to sue. If you do not accept all terms of this agreement, you should immediately return the product for a full refund. [. . . ]