User manual CARDO SCALA-700

[. . . ] See the User Manual for safety information. IMPORTANT: Please visit www. cardowireless. com/FAQ. php to check whether your particular cellular phone has any Bluetooth related bugs that may affect its operability with your headset. COMPONENTS Wheel USB Charging Jack Speaker Control Button Ear Loop Status Light scala-700 TM BEFORE USING 1. Make sure that the headset is fully charged for at least four hours before initial use. To charge the headset, plug the charger into the headset's Charging Jack, which is located just below the Wheel. When charging is completed the light will turn off. NOTE: Plugging in the charger turns off the headset. [. . . ] Insert the pin of the Ear-Loop to a suitable depth so that the speaker fits snugly into your ear (hovering above your ear canal), then bend the flexible bow of the Ear-Loop to produce a snug but comfortable fit. SWAP BETWEEN TWO ACTIVE MOBILE PHONES The scala-700 allows you to swap, i. e. to alternately use one among the last two phones to which it has been connected. While both phones are turned on and the headset is on standby, doublepress the wheel. Each time you double-press the wheel, the alternate phone connects to the Headset. 4 scala-700 TM FUNCTIONS DESIRED RESULT: Turn on the headset Turn off the headset Answer a call REQUIRED ACTION: Press the Wheel steadily for at least 3 seconds Press the Wheel steadily for at least 3 seconds Short press the Control Button NOTE: Wait until you hear the incoming call on the headset (not only on the phone) before pressing the Control Button Long press the Control Button Short press the Control Button Move the Wheel up by steps. During a call, short press the Wheel inwards During a call, long press the Control Button During standby, short press the Control button and state the name of the person you wish to call (after a tone is heard). Short press the Wheel During an active call and one call on hold or waiting, short press the Wheel. During an active call and one call on hold, long press the Wheel Reject an incoming call Terminate a call Increase the volume Decrease the volume Mute/Un-mute Transfer a call to the phone Voice Dial Redial Accept call waiting or swap between calls Conference call 5 scala-700 TM FUNCTIONS (continued) DESIRED RESULT: Locate the headset (Buzzer Function) REQUIRED ACTION: Activate the Buzzer as follows: Dial a call with the mobile phone and press Send/Talk. While the call is in progress, begin pressing the mobile phone volume buttons up, then down repeating the up/down sequence four or more times. In standby, simultaneously press the Wheel and the Control button for at least 3 seconds. Lock/Unlock buttons BATTERY MONITOR To check the status of the headset's battery, press the Control Button for at least 7 seconds while the headset is on Standby position. The Status Light will flash for 2 seconds as follows: · Blue · Red and Blue · Red Fully charged Medium charge Weak charge DISABLING / ENABLING THE STATUS LIGHT To disable/enable the Status Light, while the Headset is on Standby, move the Wheel down and hold for at least three seconds. The Status Light will stop/begin flashing, depending on whether you are disabling/enabling the Status Light. 6 scala-700 TM CHANGING THE WHEEL ORIENTATION When changing volume, the default configuration of the headset is for it to be worn on the right ear. This means that clicking up on the Wheel towards the small `+' sign on the headset increases the volume one step at a time, while clicking down towards the `-' sign on the headset decreases the volume one step at a time. If you wear the headset on your left ear, this headset allows you to change the Wheel orientation from right to left ear, so that pressing the Wheel up still increases the volume, and pressing down decreases the volume. In order to set the headset for left ear orientation: Power on the Headset by pressing and holding the Control button while pressing in and holding the Wheel for 4 seconds. Once you see 3 blue flashes, the headset is powered on and you may release the buttons. NOTE: The headset will revert to its default right ear configuration once it is turned off. In order to regularly use the headset in left ear configuration, always turn on the headset using the Control + Wheel procedure above. NOTE: If you choose to wear the headset on your left ear but do not with to change the Wheel orientation, the Wheel will function in the reverse order, i. e. [. . . ] When fully charged and charger is connected to headset, the red light indicator turns off. 10 scala-700 TM NOTE: You may have compromised the battery's capacity if you did not fully charge it prior to initial use. If you have a GSM phone and your headset is too close to the phone, interference may occur. (10m) apart or there are major obstacles such as concrete walls between the Headset and mobile phone (e. g. [. . . ]