User manual CANNON THERMOSTAT

[. . . ] Start Time 6. 00 am 8. 30 am 5. 00 pm 10. 30 pm Heat Temperature (°C) 20 °C 7 °C 21 °C 7 °C The room will be maintained at set temperature during set period. 21°C 20°C 7°C 6. 00AM 8. 30AM 5. 00PM 10. 30PM 6. 00AM Factory default settings At any time during the automatic program period, the temperature can be increased or decreased by pressing the "UP" or "DOWN" buttons. Page 2. SAFETY WARNINGS Do not place clothing or other flammable material on or near the heater. Keep curtains, clothing, furniture and other flammable materials at least 900mm from front and sides of the heater. At the owners discretion curtain clearances can be less than 900mm as long as they are restrained from the front, top and sides of the heater. The manufacturer takes no responsibility if curtain clearance is less than 900mm and not restrained. [. . . ] Note small Red LED Display light will be displayed constantly while heater is on. Will flash intermittently when unit is not in operation. With the thermostat off, press and hold the `T' button for 2 seconds or longer to initiate programming the time. Press and release the `UP ' or `DOWN ' button to increase or decrease the hour setting by 1 hour. Press and hold the `UP ' or `DOWN ' button for 2 seconds or longer to increase or decrease the hour setting by 1 hour every 0. 5 seconds. Press and release, or press and hold down the 'UP ' or `DOWN ' button to increase or decrease the minute setting by 1 minute similarly to the hour setting. Press and release the `UP ' or `DOWN ' button to change the day of the week to the following or previous day. Press and hold the `UP ' or `DOWN ' button for 2 seconds or longer to increase or decrease the day of the week by 1 day every 0. 5 seconds. In the event that Thermostat remote is in operative ie Flat batteries or damaged unit can still be used but only on the one factory setting of high fire Medium fan. Unit will start as per normal 3 minutes on Low Fire and Fan, but them will go to High Fire, Medium Fan. This switch is only for use in the event of failure of Remote Thermostat. Page 8. Manual mode. To select Manual mode, firstly the thermostat must be turned on, then press and release the `A/M' button until MANUAL appears on the display. The flame height and fan speed are set by the thermostat according to the difference between the set temperature and the current temperature. The flame height (Low or High Fire) or Fan Speeds are not manually adjustable. They are automatically controlled by the thermostat in the program cycle. This will vary according to the selected temperature and the actual room temperature. The display may show a Medium Fire symbol during operation however this function is not available with this heater and the heater will be operating on High Fire when Medium fire symbol is displayed. In the manual mode, adjust the set temperature by pressing or releasing the `UP' or `DOWN' buttons. Press and hold the `UP' or `DOWN' buttons to increase or decrease the temperature by 1°C every 0. 5 seconds. . The automatic mode allows the temperature to be regulated according to a programmed level and time. With the thermostat on, press and release the `A/M ' button until the word AUTO appears on the LCD. To correctly operate in automatic mode, the time and day of the week must be set. The thermostat will now operate according to the program set for the current time period. [. . . ] To set the period starting time, set the hour and minute setting similarly to setting the clock. Press and release the `UP ' or `DOWN' button to increase or decrease the temperature setting by 1°C. Repeat the programming process for the 4 periods. 8 10 Page 16. Back Up Switch. Fitzroy Inbuilt Model shown. Red LED flashes twice approximately every 3 seconds to indicate that power is available. When heater is operating in Back Up mode the LED is on continuously. In the rare instance of the Hand Held Unit failing to operate, the heater can be operated manually by pressing the Back Up Switch button (once). [. . . ]