User manual CANNON FITZROYIN-BUILT POWERFLUENBSPMOCK

[. . . ] Any product subjected to misuse, abuse, negligence, accident or alteration will have its warranty voided. If installation is not carried out in accordance with manufacturer's instructions, this warranty may be void. The customer must keep their "Tax Invoice" as proof of purchase of this product and compliance certificate as proof of required installation. Model number: ______________________________________ Serial number: _______________________________________ Date of manufacture: _________________________________ Date installed: _______________________________________ Compliance Certificate No: ____________________________ Designed, manufactured and distributed by: Sampford and Staff Pty Ltd. [. . . ] If your heater requires attention contact your supplier or licensed service person listed in this manual. Important: The appliance should be inspected before use and at least annually by an authorised service person. More frequent cleaning may be required due to excessive lint build-up from carpeting, bedding materials, pet hair, etc. It is imperative that control compartments, burners and circulating air passage ways of the appliance be kept clean. Do not use this fire if the glass is cracked or with the glass safety screen removed. 8 Heater Specifications Do not use fire with broken or missing logs. Gas type: Gas consumption: Energy star rating: Energy output: Heater type: Operating pressure: Gas regulator: Min. inlet pressure: Natural or Propane gas, as indicated on data label 26 MJ/hr input 3. 77 20. 7 MJ/hr Heater approved to AS 4553/AG103. Natural gas: 1. 0 kPa Propane gas: 2. 65 kPa Integral with controller (NG) 1. 13 kPa (NG) Propane gas: Regulated to supply 2. 7 kPa to appliance Fan: Controller: Minimum cavity dimensions Power requirement: Optional Accessories: Three speed Electronic Height: 605mm dimensions* Width: 700mm Depth: 393mm 240 VAC 10 A · Glass front · Gold or silver trim · Mock fireplace installation kit* · Cabinet depth spacer · Heater surround Refer fig. 8 *Note: when installing into a mock fireplace a mock fireplace installation kit must be used. Overall dimensions: 8 9 Installation instructions 1. This appliance is to be installed in accordance with the manufacturer's installation instructions, AS 5601/AG601, Municipal Building Codes, Electrical Wiring Regulations and any other statutory regulations. Remove the heater from the carton and remove the three transit screws. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Close gate over gas supply and seal around the pipe with fibreglass insulation material. Sealing is important as it prevents leakage from fan chamber into chimney: also check for gas soundness. 26 Fuel bed and log installation 16. The fuel bed is retained by a spring clip fixed to the rear of the burner chamber. Refer figure 28 FUEL BED MUST BE HARD UP AGAINST REAR OF BURNER. 27 28 17. Logs are numbered as follows: No 1 - Left front log No 2 - left back log No 3 - Right front log No 4 - Right back log Position the four individually numbered logs in the following order on the fuel bed as shown in figure 29-32. The male locating pins in fuel bed must engage with corresponding holes in the individual logs. a) Place log No. 1 onto the 2 front left pins on the fuel bed, see figure 29. 29 15 b) Place log No. 2 onto the 2 left back pins. Refer figure 30. 30 c) Place log No. 3 on single right front pin, ensure fork locates over log No. Refit the lower front cover, making sure not to damage the power cord. Important: To achieve the correct visual flame effect: On Propane the gas pressure must be set at 2. 65 kPa with burner operating on maximum setting. [. . . ] To reset the module turn off the power supply for 10 seconds and then turn the power on again. · Check the internal 3. 5 amp fuse in the module. 3 After resetting the module and appliance is still not operating. and still appliance not operating 4 · Check other connections are in place. · If the last checks are correct the ignition electrode should spark at the same time as the gas control solenoid valves open. [. . . ]