User manual CANNON CANTERBURY INBUILT

[. . . ] Cannon MAKER'S WARRANTY INBUILT MODELS CANTIB, CANTIBLP CANTIBM, CANTIBMLP USER INSTRUCTIONS INSTALLATION INSTRUCTIONS SERVICE INSTRUCTIONS This heater is approved for use with Natural and Propane gases. Please leave instructions with the owner Contents Contents Warranty Safety warnings What to do if you smell gas Warnings Standards User instructions Operating instructions Cleaning Heater specifications Installation instructions Clearances Installation into a masonry fire place Sealing Gas connection Fuel bed and log installation Gas control Gas pressure point Gas pressure sdjustment Service instructions General To replace the gas control To replace the fan To replace the electronic controller To remove the burner and electrodes To check pressures Trouble shooting Connections Electric wiring diagram Authorised service agents 18-19 17 15-16 13-14 9 10-12 6-8 2 3 4-5 2 Warranty The Cannon appliance is warranted against defects in materials and workmanship for a period of one, (1) year from its date of original purchase, for residential use in Australia. Warranty service, which includes parts and labour for the replacement or repair of defective parts, is available through Cannon Authorised Service Agencies. (Please refer to the list of authorised service agents in this manual. ) Consumers are responsible for service person's travel outside normal service areas (approximately seventy (70k) radius from the nearest Cannon dealer's location), local cartage, and normal maintenance as described in this manual. [. . . ] Model no's: CANTIBM & CANTIBMLP. Overall dimensions: 8 9 Installation Instructions 1. This appliance is to be installed in accordance with the manufacturer's installation instructions, AS 5601/AG 601, Municipal Building Codes, Electrical Wiring Regulations and any other statutory regulations. Clearances 3. Ensure the minimum clearances to combustible construction are maintained during installation, including adequate space for the proper operation and servicing of the heater. Keep curtains*, furniture and other flammable materials at least 900mm from front of heater. * Curtain clearance can be less than 900mm as long as they are restained from sides and front of heater. Note: Ensure that the combustion air opening under the heater is not obstructed. 9 10 Installation into a fireplace. 4. Models CANTIB & CANTIBLP should only be installed into a masonry or brick fireplace. Models CANTIBM & CANTIBMLP can be installed into a mock fireplace. Prepare electrical and gas connections, a 10 Amp wall socket needs to be located within 1. 5m of the heater. Hard (fixed) wiring connection is to be carried out only by a qualified electrician. Remove the heater from the carton and remove the three transit screws. Remove the front glass surround by holding it firmly on either side and pulling it towards yourself, see figure 11. 10 11 8. Remove the lower front cover by unscrewing two M5 screws through the air intake slots, see figure 12. If unit is fitted with supply flexible cord ensure that the cord cannot be trapped when the heater is installed. 12 13 9. 10. To remove the front heater surround undo two s/t screws (one either side) from the bottom flange of the front panel as indicated in figure 14. Remove the surround by pulling the lower section towards you gently to partly disengage it from the the body of the heater, then gently lift it vertically to completely disengage it. Refer figure 15. 14 15 11 Installation instructions continued 11. Seal with foam tape around top and sides of heater flange as required. Seal with fibreglass between bottom of heater case and base of fireplace. 17a 17b 13. Slide heater into the fireplace ensuring that gas inlet pipe is fed through the hole at the rear bottom RHS of the heater. Close gate over gas supply and seal around the pipe with fibreglass insulation material. Sealing is important as it prevents leakage from fan chamber into chimney: also check for gas soundness. 19 Fuel bed and log installation 16. [. . . ] At this point the spark electrode will activate for up to 10 seconds maxi mum until the flame has been established. Terminal 14 (white wire into the 8 way switch connector) will be energised as soon as the flame has been sensed. · A blue spark can be seen when the heater ignition process starts. · Check that there is no short circuit to earth and spark gap is correct. [. . . ]