User manual CANDY CDI2D36

[. . . ] The guarantee applies to Gt Britain and Northern Ireland only, and is an addition to your statutory rights. AFTER SALES SERVICE For service and repairs call your local engineer on our national telephone number: GIAS Service Support Service Tel: 08444 995599 (Eire 0818 200021) 12 DESCRIPTION OF THE CONTROL PANEL A B C D E "ON/OFF" button "PROGRAMME SELECTION" button "DELAY START" button "EXPRESS" option button "ALL IN 1" option button F G H I DIMENSIONS "START"/"RESET" button (start/cancelling programme) "OPTION SELECTION" lights DIGITAL DISPLAY Programme guide Width x Height x Depth (cm) Depth with door open (cm) 59, 8 x 81, 8 ÷ 89, 8 x 55 117 TECHNICAL DATA EN 50242 place load Capacity with pans and dishes Water supply pressure (MPa) Fuse / Power input / Supply voltage 13 8 persons Min. 0, 8 See rating plate CONSUMPTION (main programmes)* Energy (kWh) Water (L) HYGIENIC 2, 00 19, 5 UNIVERSAL 1, 38 13, 5 ECO 0, 92 10 RAPID 24' 0, 59 9 Power consumption of the off-mode and of the left-on mode: 0, 45 W / 0, 45 W *Values are measured in a laboratory according to European Standard EN 50242 (consumption may vary according to conditions of usage). However, if the door is opened while a programme is running (for example, to add dishes) the machine stops automatically and the display will flash the remaining time before the end of the cycle. [. . . ] This programme is recommended for light soil washes, and for slightly wet dishes that are not fully dry, & improved drying results. We advise you to leave the door of the Dishwasher half-open at the end of the cycle, to allow for a natural circulation of air inside the dishwasher. "DELAY START" button Dishwasher start time can be set with this button, delaying start from 1 to 23 hours. Proceed as follows to set a delayed start: ■ Press the "DELAY START" button ("00" will appear on the display). By pressing this button, the selected washing programme is modified to get best performance from combined detergents (furthermore, the salt empty alert will be de-activated). – Press the button again to increase the delay in hours (each time the button is pressed the delay is increased by 1 hour to a maximum of 23). Once selected, this option keeps being on (light on) also for next washing cycles and it can be de-activate (light off) only by pressing the button once again. If you wish to see which programme has been selected, press the "PROGRAMME SELECTION" button. Press the same button again ("b0" will appear on the display to indicate that the alarm is off). "00" will appear on the display and some audible signals will sound. Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. IMPORTANT The dishwasher must ALWAYS be off before start of this procedure. Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). Hold down the "PROGRAMME SELECTION" button and at the same time switch on the dishwasher by pressing the "ON/OFF" button (a brief audible signal will sound). Keep the "PROGRAMME SELECTION" button pressed for at least 30 seconds (during this time, 3 audible signals will sound). Release the button when the THIRD audible signal sounds ("A0 " will appear on the display to indicate that the memorization is off). Press the same button again ("A1" will appear on the display to indicate that the memorization is on). Keep the "PROGRAMME SELECTION" button pressed for at least 15 seconds (during this time 2 audible signals will sound). Release the button when the second audible signal sounds ("b1" will appear on the display to indicate that the alarm is on). Turn off the dishwasher by pressing the "ON/OFF" button to confirm the new setting. IMPORTANT This dishwasher is equipped with an anti-overflow safety device which will automatically discharge any excess water should a problem occur. To ensure the correct operation of the anti-overflow safety device, we recommend that the dishwasher is not moved or tilted during operation. [. . . ] In the event of damage occurring to the main inlet pipe any water leakage is retained within the transparent hose. If water has leaked from the main inlet pipe there will be a visible sign within the transparent hose. You may continue to complete the programme cycle but for safety we recommend the immediate replacement of the complete hose assembly. If the hose is not long enough for correct connection, it must be replaced with a longer one. [. . . ]