User manual CAMBRIDGE SOUNDWORKS MEGAWORKS 210D

[. . . ] ACCESSORIES ­ Do not place the speaker on an unstable cart, stand, tripod, bracket, or table. The speaker may fall, causing serious injury to a child or adult and serious damage to the product. VENTILATION ­ Slots, openings and metal fins in the cabinet are provided for ventilation, to ensure reliable operation of the speaker and to prevent it from overheating. These areas must not be blocked or covered such as by placing the product on a bed, sofa, very deep pile rug, or other similar surface. [. . . ] J) Stereo Signal Cable, Green Miniplug to Green Miniplug Plugs into analog LINE IN A or LINE IN B Connect to any analog sound source with a 3. 5 mm stereo output jack, like Cambridge SoundWorks MusicWorksTM, a portable CD player, a small headphone jack, or a computer sound card. A B C No. 10 screws and plastic wall anchors D E F G H To Signal Source Signal Cables To MegaWorks I J 5 SETUP OPTIONS Cambridge SoundWorks, Inc. supplies screws and plastic anchors for convenience, but it is the speaker purchaser's responsibility to insure that any speaker placement is secure, stable and reliable. Cambridge SoundWorks assumes no responsibility for damage to its products or any damage to property resulting from speaker positioning or placement. A SUBWOOFER/AMPLIFIER The Subwoofer/Amplifier requires no assembly. SATELLITES Desktop Placement Each satellite is shipped with a Desktop Stand installed. You can also install the Volume Control to a Desktop Stand (see page 12). Some program sources (stereo televisions, portable CD players) provide their own output level adjustment. The volume control is optional in these cases. B Shelf Placement (or other flat surface) without the Desktop Stand A) Desktop Stand Removal: unscrew the thumbscrew to release the satellite. B) Apply the soft, self-adhesive feet to the bottom surface of each satellite, as shown. Apply Feet to Bottom for Shelves C Apply Feet to Back for Wall Mounting on Screwhead Wall Mounting With Supplied Hardware Note: Use the "hook and loop" fastener to secure the volume control to a convenient flat surface if not using the Desktop Stand C) Apply the soft, self-adhesive feet to the back of the satellite as shown. The feet improve stability mounting and protect the finish of both the wall and the satellite. D) Install the No. 10 screw and anchor in the wall so that its screwhead protrudes about 3/8 inch. E) Adjust the screw so each satellite can be hung with just a small amount of pressure. D E Install Mount Speaker 6 Wall Mounting With A Swivel Bracket Contact Cambridge SoundWorks about available swivel brackets. F) Follow the installation instructions for your particular mounting bracket to attach it to a flat surface. This places the bracket above the satellite, concealing it when viewed from below. In this case, remove, invert and re-install the the satellite grille to position the logo correctly. F Remove, Invert and Replace Grille Panel Floor Stands G) Follow the instuctions included with the Newton ST300 Floor Stands to install the satellites. G Using Speakers on a Stand 7 CONNECTION DIAGRAM RED DIGITAL OUT I Yellow/Orange plug ­ to a minijack digital output (for instance, a Sound Blaster Live!5. 1 sound card) Digital Signal Cable PO BASS TREBLE + + Analog Signal Cable J Green plug ­ to a stereo minijack analog output (MusicWorks, sound card, portable CD player) 8 RED WER/STANDBY DIGITAL IN SPEAKERS + L LINE IN A R B VOLUME CONTROL + 120VAC 60Hz POWER RISK OF FIRE REPLACE FUSE AS MARKED 9 POSITIONING YOUR SPEAKERS SUBWOOFER/AMPLIFIER Place the Subwoofer cabinet on the floor, preferably near a wall. If the subwoofer is placed away from the intersection of two room surfaces, the maximum bass output will be reduced. Use the Bass Level control to adjust the bass output to your desired balance. Recommended Bass control settings for each type of location are shown. Maximum Bass Output BASS Moderate Bass Output BASS Least Bass Output BASS Suggested Bass Control Compensation + SATELLITES Desktop Placement The Desktop Stands improve the sound for both a standing or seated listener. + + MusicWorks Position the satellites so they form a 45 degree angle from your listening position. 45 ° le ang le ang 45 ° 10 POSITIONING THE SATELLITES Wall Placement Avoid facing a satellite parallel to a nearby wall (within 6-8 inches). The reflected sound from the wall degrades the sound coming directly from the satellite (diagram A). Try to position wall-mounted satellites so both are approximately at your ear level while sitting or slightly higher. Make sure the speakers form at least a 20degree angle with your listening position. An angle greater than 55 degrees sounds like two separate speakers, rather than forming a continuous image of sound between the two speakers (diagram B). [. . . ] 3) If possible, play a variety of musical CDs with good deep bass content to judge the best setting of the Bass and Treble controls. BASS TREBLE + + Cleaning The painted surfaces of the satellites and subwoofers should be wiped with a damp cloth or brushed clean. The grille panel material can be vacuumed or brushed clean. 16 SPECIFICATIONS Analog Input: 775 millivolts for full output 10 kohms input impedance FUSE REPLACEMENT IMPORTANT: Turn off and unplug the speaker before changing the fuse. Digital Input: Supports 32 kHz, 44 kHz, 48 kHz and 96 kHz data rates, any word length up to 24 bits. Amplifiers: Satellite: 60 watts continuous at 1 kHz, two channels driven at less than . 1% total harmonic distortion. Subwoofer: 150 watts continuous at 100 Hz, one channel driven at less than . 3% total harmonic distortion. System Frequency response: Satellite: 150 Hz to 15 kHz, +/- 3 dB Subwoofer: 32 Hz to 150 Hz +/- 3 dB Use only with a 250V fuse Employer uniquement avec un fusible de 250V 2. 3. Drivers: Nominal 8 inch subwoofer driver Nominal 3. 5 inch satellite driver AC Voltage: 120VAC, 60Hz Dimensions (H x W x D) and Weights Satellite (without stand) 4 1/2" x 4 3/8" x 4 7/8" 113mm x 108mm x 125mm 1 pound, 1ounce 482 grams Satellite (with stand) 6 1/4" x 4 3/8" x 5 5/8" 160mm x 108mm x 143mm 1 pound, 3 ounces 539 grams Subwoofer 11 1/8" x 10" x 10" 263mm x 255mm x 255mm 14 pounds, 8 ounces 6. 6 kg 4. 5. Fuse Replacement The fuse holder is located in the power connector at the base of each speaker. [. . . ]