User manual CAMBRIDGE AUDIO INCOGNITO LK10 EU INSTALLATION GUIDE

[. . . ] I. C. P - In-circuit programming socket, used to upgrade keypad software when necessary. 5 Installation notes The LK10 is fitted on the wall by fixing it into a standard UK 47mm depth double-gang electrician’s back-box (pattress). All knock-outs in the back-box should be removed to provide maximum ventilation. Where it is desired to fit a mains lighting switch etc next to a keypad, a barrier-box or two single backboxes must be used (bear in mind it is not preferable to fit the keypad next to a light-switch particularly if the faceplate styles will differ). Avoid fitting the LK10/KP10 where there is line of sight to another LK10/KP10. [. . . ] The Incognito LR10 is a sophisticated learning remote which is able to learn the codes of all the source equipment from their own remotes. Once the LR10 itself has been programmed the user can clone all macros and programmed information from the LR10 to the LK10, allowing the keypad to also perform the same operations (IR codes, macros, button names and clock settings). Note: Only the learning buttons highlighted on the remote are cloned to the LK10. Please refer to the LR10’s own manual for full details on how to teach codes into the LR10, advice on macros etc. Once the LR10 is fully programmed/setup, you can clone it into the LK10. To begin cloning, plug the supplied connection cable into the cloning port on the LK10 and LR10, then put the LK10 into Learn mode. On the back of the LR10 press the Edit button 4 times (using a paperclip or similar) to enter Clone mode. ‘REC/TRX’ will appear on both displays. Shift Fav-1 (Set) Menu Title Exit 10 LK10 For the LK10 to receive commands, it must be first put into Learn mode. The LK10 has a series of menus that can be accessed by pressing and holding the Shift/Set button on the front panel. The menu options are continuously scrolled on the LK10 display until you release the Shift/Set button. Follow the next steps to complete the cloning operation: ENGLISH LK10 keypad - Receiving data 1 2 LR10 remote - Transmitting data 1. Press the is flashing. button on the remote until ‘TRX’ 4. ‘RXING. . ’ will then be displayed, to indicate it is receiving data. 3. Display shows ‘SENDING’. 11 Cloning from the remote control continued After approximately 7 minutes the keypad display should show ‘COMPLETE’ and return to normal operation. If the clone fails the keypad will show ‘ERROR’ or ‘TIMEOUT’. Put the transmitting LR10 remote back into Clone mode and repeat the process. Note: Once the cloning process has been started it must be completed, as it overwrites the software in the receiving LK10 keypad. 12 LK10 Note: You still use your KP10 keypad to control audio functions (volume adjustment, source selection etc). To personalise other settings of the LK10, press and hold the Set button for four seconds to activate the Settings menus (Fig. The LK10 screen will continuously scroll through the five menu options: Learn 1 Alarm 2 Sleep Setup 3 Configure Shift Fav-1 Shift Fav-1 Shift Fav-1 (Set) Menu Title Exit (Set) Menu Title Exit (Set) Menu Title Exit To select the option you require release the button when the menu option is displayed on the screen (Fig. Any changes you have made will be saved. 13 ENGLISH Settings menus Settings menus continued Alarm menu Press the Set button for five seconds and release when ‘ALARM?’ is displayed on the screen. Alarm Hour Minute Days Source On/Off Shift Fav-1 (Set) Menu Title Exit Use the and desired option. buttons to navigate the menu. Use the and buttons to adjust the Note: When a Source is selected, it will display the default Source programmed into the KP10 keypad. Days When selecting ‘DAYS’, use the Friday, weekend or everyday. [. . . ] You may call Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and/or you purchased from a Cambridge Audio authorised dealer. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of, or to any part of, the product. This warranty does not cover damage due to improper operation, maintenance or installation, or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer, or authorised service agent which is authorised to do Cambridge Audio warranty work. REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. [. . . ]