User manual CAMBRIDGE AUDIO INCOGNITO KP10 CU INSTALLATION GUIDE

[. . . ] As part of a full Incognito system, where it is plugged into an Incognito hub (AH10), perhaps with other Incognito accessories such as a video switching unit (VH10) or local input module (LM10) fitted. Where the keypad is plugged directly into an A-BUS Ready/Incognito Ready output of a compatible Cambridge Audio (or other brand) A/V Receiver or Amplifier, no other accessories are possible other than the required power supply and remote control/s. The KP10 has two modes of operation to support these configurations, AH10 mode and Standard A-BUS/Incognito Ready mode. The modes are selected by setting the Mode switch, located on the rear of the KP10. [. . . ] Connect each wire in the Cat-5 cable to its respective terminal in the screw-down connector on the back of the KP10 (refer to the Cat-5 to KP10 screw-down connectors diagram in the `Rear panel connections' section of this guide). The recommended maximum length for use with standard Cat-5 cable is 30m from hub to keypad in total (screened Cat-5 cable can also be used). After making the wiring connections, fit the KP10 to the back-box with the two supplied 6x32 UNC 35mm screws. Note: If in doubt about any aspect of installation or wiring, seek professional advice from a qualified installer. Incognito A-BUS keypad 9 REAR PANEL CONNECTIONS 1 orange / white brown / white green / white Cat5 to KP10 screw-down connectors 1 A Cat-5 cable (terminated with an RJ45 jack plug) is used to connect the KP10 to an AH10 hub or A-BUS Ready receiver. The KP10 has screw-down connectors for the eight individual conductors of the Cat-5 cable (use a small flat-bladed screwdriver). See below for the EIA/TIA 568A wiring standard: blue / white 2 12345678 orange brown green blue R+ RLL+ 3 1 4 7 2 View from contact end 1 2 3 4 5 6 7 8 white /green green white /orange blue white /blue orange white /brown brown AH10 6 3 Std. A-BUS/ Incognito Ready 5 R+ R - L- L+ 10 Incognito A-BUS keypad Gather pairs, trim and insert into RJ45 plug 4 Crimp wires securely in place KP10 A-BUS keypad 2 Gain adjust The maximum output of the KP10 can be limited by turning these down. Alternatively, if the sound level is too quiet, the Gain can be turned up. 3 Mode switch I. C. P Speaker output Selects between AH10 mode and Standard A-BUS Ready/Incognito Ready mode. 4 In-circuit programming socket, used to upgrade keypad software when necessary. 5 Connect to a pair of speakers with two runs of standard high-quality speaker cable. Speakers of at least 88 dB SPL for 1W @ 1 metre efficiency should be used with the KP10. The Incognito SS10 speakers are an ideal match. 6 LK10 option Allows control of source equipment via an LK10 Learning Keypad. 7 Preamp output A preamp output is provided for optional use driving a powered subwoofer or auxiliary amplifier. Connection from the preamp output to other equipment should be by screened audio cable (see diagram below). Line-in/Line-out connections on subwoofer Screened audio cable Preamp output connections on rear of KP10 Incognito A-BUS keypad 11 KEYPAD CONTROLS The six LEDs indicate the function status of the KP10. Listed below are each of the functions of the corresponding LEDs: 3 2 1 4 1 5 6 2 Volume / Source select / Bass adjust / Local Source Selection Mode 3 Volume / Source select / Treble adjust / Local Source Selection Mode 7 9 4 Volume / Source select / Balance adjust / Local Source Selection Mode 5 Volume / Source select / Fader adjust / Local Source Selection Mode 6 12 Minimum volume / Source select 8 11 10 Maximum volume / Source select For full instructions on volume adjustment, source selection, sound adjustment and local source selection modes, refer to the `Operating instructions' section of this guide. 12 Incognito A-BUS keypad KP10 A-BUS keypad 7 Standby/On Press to switch the keypad between On and Standby mode. By pressing and holding the Standby button for about 2 seconds, all KP10s connected to the AH10 hub will be turned off. In this mode pressing the Volume up/down keys will adjust the Treble (high frequencies) level. Continuing to hold both buttons will light the fourth LED indicating that Balance adjust mode has been activated. In this mode pressing the Volume up/down keys will adjust the sound level between the left and right speakers. Continuing to hold both buttons will light the fifth LED indicating that Fader adjust mode has been activated. In this mode pressing the Volume up/down keys will adjust the balance between the main speakers and anything that is connected to the preamp output. The volume up and down buttons on the remote control can also be used to adjust the sound in each mode. Note: If no adjustment is made the system will automatically go back to volume adjustment after two seconds. Bass Treble Balance Fader Incognito A-BUS keypad 15 LOCAL SOURCE SELECTION Note: This feature is only available if the KP10 is part of a full Incognito multi-room system with one or two Local Input Modules (LM10) fitted. The local source selection mode will need to be activated to configure the KP10 correctly. This mode is only available when the Mode Switch is set to "AH10" mode. [. . . ] You may call Cambridge Audio or your local country Cambridge Audio distributor to confirm that you have an unaltered serial number and/or you purchased from a Cambridge Audio authorised dealer. This warranty does not cover cosmetic damage or damage due to acts of God, accident, misuse, abuse, negligence, commercial use, or modification of, or to any part of, the product. This warranty does not cover damage due to improper operation, maintenance or installation, or attempted repair by anyone other than Cambridge Audio or a Cambridge Audio dealer, or authorised service agent which is authorised to do Cambridge Audio warranty work. REPAIRS OR REPLACEMENTS AS PROVIDED UNDER THIS WARRANTY ARE THE EXCLUSIVE REMEDY OF THE CONSUMER. [. . . ]