User manual CALCULATOR & CALENDAR DOUBLE PRESS UP CALCULATOR & CALENDAR

[. . . ] • When using a power cord (purchased separately), be sure to place the fuse near the battery as shown. • Connect the lead wire (power cord) through which power is supplied directly to the battery’s “ª” terminal only after all the other connections have been made. • + B and GND: AWG 8 to AWG 4 (The cross section is about 8 mm2 to 21 mm2. ) • REM: AWG 18 to AWG 8 (The cross section is about 0. 8 mm2 to 8 mm2. ) a When you use CALCULATOR & CALENDAR car receiver with a remote lead, connect to the REM terminal on this unit. b When you connect a unit without a remote lead, connect to the accessory circuit of the car which is activated by the ignition switch. [. . . ] • When mounting the unit under the front seat, make sure that adjusting the seat position will not catch any wire of the unit. TERMINAL CONNECTIONS When making terminal connections, properly fix each terminal with the provided screw by turning it as illustrated. • Use ring terminals (not provided) for secure connection. Notes • Make sure the screw is fixed in place to prevent disconnections. • Avoid over-tightening as it may cause the damage to the screw or its head slot. ı Install the unit Provided screw φ 4 × 20 mm (13/16 in. ) • When mounting this unit, be sure to use the provided screws. • If any other screws are used, there is a risk of loosening the unit or damaging the parts under the car floor. • Before drilling holes in the trunk to install the unit, make sure that there is a sufficient space under the trunk so that you do not drill holes in the fuel tank, etc. Drilled hole SPEAKER SYSTEMS Notes • Be sure not to connect the “·” terminals of the speakers to a common point. • If the same lead is used for both left/right or front/rear speaker wirings, this unit cannot be used. • Use the speakers with an impedance of 2 Ω to 8 Ω (4 Ω to 8 Ω: when used in Bridge Mode). The proper lead connected to each SPEAKER OUTPUT terminal is as follows. KS-AX3104/KS-AX3102: AWG 18 to AWG 12 (The cross section is about 0. 8 mm2 to 3. 3 mm2). DOUBLE PRESS UP CALCULATOR & CALENDAR: AWG 18 to AWG 8 (The cross section is about 0. 8 mm2 to 8 mm2). SAFETY INSTRUCTIONS “SOME DOS AND DON’TS ON THE SAFE USE OF EQUIPMENT” This equipment has been designed and manufactured to meet international safety standards but, like any electrical equipment, care must be taken if you are to obtain the best results and safety is to be assured. Select the appropriate connection referring to the following diagrams. KS-AX3102 2-speaker system—Normal Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. Notes • Securely connect all the parts. If the connections are loose, due to contact resistance etc. , heat will break out and may cause an accident. • Run the connection leads under the car mats to prevent accidental disconnections. ı When your receiver is NOT equipped with line output. KS-AX3104 KS-AX3102 DOUBLE PRESS UP CALCULATOR & CALENDAR Å CALCULATOR & CALENDAR car receiver, etc. Line out ı Speaker input connector. Connector lead a White "LEFT (+)" b Black "RECEIVER GND" To Receiver = Left (+) lead = Chassis*1 = Right (+) lead *2 INPUT HIGH INPUT L/MONO LEVEL c Gray "RIGHT (+)" CROSSOVER LPF OFF HPF FRONT REAR MIN MAX R • Connect each lead of the speaker input connector to a speaker positive lead or chassis*1 of the receiver. • Cover the terminals of unused speaker negative leads of the receiver with insulating tape to prevent short circuits. *1 Example: connecting to the ground Rear ground terminal Black lead of the speaker input connector RECEIVER GND 2-speaker system plus subwoofer • Use the speakers with an impedance of 2 Ω to 8 Ω. Line out (Rear) or Subwoofer out Å CALCULATOR & CALENDAR car receiver, etc. (Purchased separately) CALCULATOR & CALENDAR car receiver, etc. Line out (Front) *2 INPUT FRONT REAR ı Speaker input connector. Connector lead a White "LEFT (+)" b Black "RECEIVER GND" c Gray "RIGHT (+)" CROSSOVER LEVEL LPF OFF HPF *2 Not supplied To Receiver Subwoofer = Left (+) lead = Chassis*1 = Right (+) lead KS-AX3104 4-speaker system—Normal Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. Line out (Front) * 2 HIGH INPUT L/MONO Front MIN MAX R * 2 Rear Line out (Rear) HIGH INPUT LEVEL CROSSOVER LPF OFF HPF Subwoofer system—Bridge Mode Rear • Use the speakers with an impedance of 4 Ω to 8 Ω. Å CALCULATOR & CALENDAR car receiver, etc. CROSSOVER LPF OFF HPF HIGH INPUT LEVEL INPUT L/MONO L/MONO ı Speaker input connector. Line out (Rear) or Subwoofer out *2 Connector lead a White "LEFT (+)" b Black "RECEIVER GND" c Gray "RIGHT (+)" CROSSOVER LEVEL LPF OFF HPF MIN MAX MIN MAX To Receiver R R = Left (+) lead = Chassis*1 = Right (+) lead FRONT REAR ı Speaker input connector. Connector lead a White "FRONT LEFT (+)" b Black "RECEIVER GND" c Gray "FRONT RIGHT (+)" To Receiver 1 Connector lead d Green "REAR LEFT (+)" e Black "RECEIVER GND" f Purple "REAR RIGHT (+)" To Receiver INPUT HIGH INPUT L/MONO = Front left (+) lead = Chassis* = Front right (+) lead = Rear left (+) lead = Chassis* 1 MIN MAX = Rear right (+) lead R Subwoofer 2-speaker system plus subwoofer—Bridge Mode • Use the speakers with an impedance of 2 Ω to 8 Ω. [. . . ] • Be sure to connect the line output from the receiver to the left (L) jack on this unit. Line out (Front) TROUBLESHOOTING The POWER indicator does not light. • Change the fuses if the current one is blown. • Leave the unit turned off to cool it down if it heats up abnormally. Å CALCULATOR & CALENDAR car receiver, etc. *2 *2 CALCULATOR & CALENDAR amplifier, etc. (Purchased separately) Line out (Center) *2 Subwoofer out Line out (Rear) ı Speaker input connector. *2 PRE OUT L INPUT HIGH INPUT L/MONO Front Speaker Rear Speaker No sound is heard. • Confirm the connections for the power supply (see "POWER SUPPLY" on page 1). [. . . ]