User manual CAKEWALK REAC

[. . . ] SONAR User's Guide TM Recording System Information in this document is subject to change without notice and does not represent a commitment on the part of Twelve Tone Systems, Inc. The software described in this document is furnished under a license agreement or nondisclosure agreement. The software may be used or copied only in accordance of the terms of the agreement. It is against the law to copy this software on any medium except as specifically allowed in the agreement. [. . . ] Click OK again and then click Close to close the window. Windows Vista: Additional Options Windows XP: Other Control Panel Options 7. The driver displays a dialog asking that the SPS/ FA-66 be turned off and back on before the changes will take effect. Set the Sample Rate switch to the same rate as the Digital Snake. SONAR 7 Producer Setup 1. If the No MIDI Outputs Selected dialog is displayed, select the Don't show this again check box and click Continue With No MIDI Output. If the No MIDI Inputs Selected dialog is displayed, select the Don't show this again check box and click Continue With No MIDI Input. If a message box about MIDI controllers and control surfaces is displayed, click No. 3. Click the following items depending on your operating system. 20 · SONAR REAC Recording System User's Guide · · · · · 8. Close and restart SONAR. please see "About the REAC Control Panel" on page 22. g) In the REAC Inputs box, select the number of ports that you want to record. English English h) Click OK to close the SONAR REAC Driver control panel. Confirm the following settings: a) On the Options menu, click Audio to open the Audio Options dialog. b) Click the General tab c) Click ASIO Panel to open the SONAR REAC Driver control panel. For information about other available Sync Modes Note: Make sure that the Enable Read Caching and the Enable Write Caching check boxes are cleared. o) On the Option menu, click Global to open the Global Options dialog. m)If SONAR is running in Windows Vista, clear the Use MMCSS check box. English English PC Setup · 21 · · · · · Note: The Audio Path must be set to a folder which is located on the audio recording drive. 6. A new project is created. About the REAC Control Panel The following section describes the controls in the SONAR REAC Driver Panel. Preferred Sync Setting Locked Create a New Project Note: 8, 16 and 40 channel REAC recording templates are included with SONAR. When this mode is selected, REAC is the clock master for both SONAR and the SPS/FA-66. Use this option when there is a physical clock connection between the SPS/FA-66 and the AES/EBU or Word Clock output on the REAC hardware system. This is the most desired sync mode setting for this recording system. 1. In the Location box and Audio Path box, specify the hard drive that you use for audio recording. Alternate Sync Settings There may be situations where it is not possible to have a dedicated clock connection between the REAC hardware and the SPS/FA-66 monitoring device. The following are alternative clock settings in the SONAR REAC Driver Control Panel. Please be advised that any of the settings below will either increase latency or create gaps, pops, clicks or other noise during audio playback. Freewheel (Re-sync) When this mode is selected, REAC is the clock master for SONAR only. Use this option only if it is not possible to have a physical clock connection between the SPS/FA-66 and the AES/EBU or Word Clock output on the REAC hardware system. [. . . ] HOWEVER, CAKEWALK DOES NOT WARRANT THE OPERATION OF THE PRODUCT OR THE ACCURACY OR COMPLETENESS OF ANY INFORMATION CONTAINED IN THE PRODUCT. Subject to the other provisions in Articles 4 and 5 of this Agreement, Cakewalk warrants to you, the original licensee, that the media on which the Product is recorded will be free of defects in material and workmanship under normal use for a period of thirty (30) days from purchase, and that the Product will perform substantially in accordance with the user guide for a period of thirty (30) days from purchase. Cakewalk's sole responsibility under this warranty will be, at its option, (1) to use reasonable efforts to correct any defects that are reported to it within the foregoing warranty period or (2) to refund the full purchase price. Cakewalk does not warrant that the Product will be error free, nor that all program errors will be corrected. [. . . ]