User manual BUSHNELL IMAGEVIEW 78-7348 (NO USB MASS STORAGE)

[. . . ] When camera is connected to a PC via the USB cable provided, the camera will power on automatically 2. Power off: While camera is on, press and hold button until camera turns off. If camera has not been used or if a button has not been pressed for over 2 minutes, the camera will automatically power off to save battery life. If the camera is connected via USB, camera will not power off except when PC powers off. [. . . ] When in "Normal" mode press MODE button twice to change to "Repeat Shot" mode. When you see the " " icon blinking, " icon will stop press SNAP to enter this mode (the " blinking). By pressing and holding the SNAP button you will now be able to take 3 consecutive pictures. The camera will remain in this mode until you change the mode or until the camera's memory is full. When memory is full the display will show "FUL" and an alarm will sound. Alarm will sound 6 12. To enter "Low Resolution" mode, which will cause your pictures to be of a lower resolution, but will also allow you to store many more pictures in the camera's memory, press the MODE button 3 times until you see the "LQ" icon blinking. Entering this mode later and pressing SNAP again will return you to "High Resolution" mode. When in "Normal" mode press the MODE button 4 times to enter the "AVI" mode. Holding down the SNAP button will take AVI clips as long as you continue to depress the button or until the memory is full. Once you release the button the camera will revert back to "Normal" mode so you can take still (i. e. Repeat step 11 if you want to change the camera to the AVI mode again. 15. If "Delete Last" mode is selected, the display will show the following: delete last picture then quit this mode Press SNAP to delete the last picture from the camera's memory. If "Delete All" mode is selected, the word "ALL" appears next to the icon on the display. If no button is pressed for a while, the camera returns to stand-by. 14. You can chose between the 50mhz and 60mhz settings for the camera output. The camera's default mode is the "60" mode, which matches the power frequency for the United States. To change to the "50" mode, press the SNAP button until the "60" changes to "50. " Confirm the selection by pressing the SNAP button. To avoid any flickering on the picture, the correct power frequency (either 50 or 60) for your country must be selected. 17. If the "Battery" indicator is only one third highlighted, it is necessary to replace the batteries soon. the " " icon will blink and buzzer will sound 7 8 18. If the camera is connected to your PC via USB cable, the display will show 8. Click on the "Download photos" button (round red camera icon on bottom left) to start the download from the ImageView to your computer. When the download is finished, you should see "thumbnail" preview frames showing DOWNLOADING THE PICTURES TO YOUR COMPUTER: 1. [. . . ] Unauthorized service may also void the warranty. 11 12 TWO-YEAR LIMITED WARRANTY Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. In the event of a defect under this warranty, we will, at our option, repair or replace the product, provided that you return the product postage prepaid. This warranty does not cover damages caused by misuse, improper handling, installation, or maintenance provided by someone other than a Bushnell Authorized Service Department. Any return made under this warranty must be accompanied by the items listed below: 1) 2) 3) 4) 5) A check/money order in the amount of $10. 00 to cover the cost of postage and handling Name and address for product return An explanation of the defect Proof of Date Purchased Product should be well packed in a sturdy outside shipping carton, to prevent damage in transit, with return postage prepaid to the address listed below: IN CANADA Send To: Bushnell Performance Optics Attn. : Repairs 25A East Pearce Street, Unit 1 Richmond Hill, Ontario L4B 2M9 WARNING Make sure you download any pictures from your camera BEFORE you remove the batteries from the camera. 2 AAA Batteries Required, Not Included IN U. S. A. [. . . ]