User manual BUFFALO WZR-HP-G450H

[. . . ] User Manual for Professional Firmware WZR-HP-G450H Nfiniti High Power Wireless N Router & Access Point www. buffalotech. com 35012039 ver. 01 Introduction 1. Wireless -1- 3 3 3 3 3 3 4 4 4 5 6 6 6 7 7 7 8 8 8 9 11 11 12 12 12 12 12 13 13 14 14 14 14 14 14 14 14 14 14 15 15 15 15 15 15 15 16 16 16 16 16 16 16 16 16 17 17 2. 3. 8. 5. GNU General Public License ­ Terms and Conditions or Copying, Distribution and Modification 4. 1. 3. NO WARRANTY 17 17 18 18 18 19 20 21 23 23 25 25 27 27 27 28 31 -2- 1. [. . . ] If username and password fields are displayed, enter "root" for the username. Enter "admin" for the password if you're using the professional firmware (default), or leave the password field blank if you've switched to the user-friendly firmware. Refer to Chapter 4 for advanced settings. Firmware Differences You can choose between two different firmwares for your AirStation. By default, the professional firmware (dd-wrt) is preinstalled for US/EU products. The two firmwares have slightly different features, as shown in the chart below. Function Router mode switch functionality Default administrator name Default administrator password AOSS WPS WDS Professional firmware (dd-wrt) User-friendly firmware root admin a root (fixed) none a a a a WZR-HP-G450H User Manual 20 Chapter 3 Installation Changing Firmware To change between the professional firmware (dd-wrt) and the user-friendly firmware, follow the steps below. Windows 1 2 Insert the AirNavigator CD into your computer. The setup wizard will automatically launch. Note: If the Setup Wizard does not launch, open the CD and double-click [ASSetWiz. exe] in the "Win" folder. Click [Change Firmware]. 3 The procedure for wiring will be displayed. Step through the wizard to connect your AirStation. WZR-HP-G450H User Manual 21 Chapter 3 Installation 4 When this screen is displayed, click [Change Firmware]. 5 If requested, enter the AirStation's username and password. Note: By default, the professional firmware doesn't have a username and password configured. Set them before you go to the next step. WZR-HP-G450H User Manual 22 Chapter 3 Installation 6 When the following screen is displayed, make sure that the firmware file name is displayed, click [Upgrade] or [Apply], and follow the instructions on the screen. Note: If the firmware name is not displayed on the screen, click [Browse. . . ] and select the desired firmware. The firmware files are contained in the "Firmware" folder of the AirNavigator CD. Professional firmware (dd-wrt) update screen: User-friendly firmware update screen: WZR-HP-G450H User Manual 23 Chapter 3 Installation Macintosh 1 2 Open the configuration Interface of the AirStation. To replace the professional firmware with the user-friendly firmware, click [Administration] > [Firmware Upgrade]. To replace the user-friendly firmware with the professional firmware, go to [Easy Setup] and click [Update AirStation Firmware]. Click [Browse. . . ] to select the firmware file, and click [Upgrade] or [Apply]. Note: The firmware files are contained in the "Firmware" folder of the AirNavigator CD. 3 Professional firmware (dd-wrt) update screen: WZR-HP-G450H User Manual 24 Chapter 3 Installation User-friendly firmware update screen: WZR-HP-G450H User Manual 25 Chapter 4 - Configuration The web-based configuration tool lets you change advanced settings for the AirStation. Don't change these settings unless you know what you're doing. Accessing the Web-based Configuration Interface To configure the AirStation's advanced settings manually, log in to the web-based configuration interface as shown below. 1 2 Launch a web browser. Enter the AirStation's LAN-side IP address in the address field and press the Enter key. Note: · The AirStation's default LAN-side IP address depends on the position of the mode switch. In router mode: 192. 168. 11. 1 In bridge mode: 192. 168. 11. 100 Note: If the router switch is set to auto and the unit is in bridge mode, then the AirStation's IP address was assigned by an external DHCP server. · If you changed the IP address of the AirStation, then use the new IP address. 3 When this screen appears, enter "root" (in lower case) for the username and the password that you set during initial setup. Click [OK]. Note: · By default, the password is blank (not set). · If you forget your password, hold down the reset button (page 13) to initialize all settings. Note that all other settings will also revert to their default values. WZR-HP-G450H User Manual 26 Chapter 4 Configuration 4 This is the configuration interface, where most AirStation settings can be configured. Refer to the Help screens for more information on using the configuration interface. WZR-HP-G450H User Manual 27 Chapter 4 Configuration Configuration Interface Menus in Router Mode The menu structure for the AirStation in router mode is as follows. Please refer to the pages listed at right for explanations of each item. Main screen Internet/LAN Internet PPPoE 3G Modem DDNS VPN Server LAN DHCP Lease NAT Route Wireless Config WPS Basic Advanced WMM MAC Filter Multicast Control Guest Port AOSS Security Firewall IP Filter VPN Passthrough LAN Config Port Forwarding Descriptions Configure Internet side port and settings. Network address translation settings, used to connect LAN side devices to the Internet. [. . . ] deklaruoja, kad sis AirStation WZR-HP-G450H atitinka esminius reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. dat het toestel AirStation WZR-HP-G450H in overeenstemming is met de essentiële eisen en de andere relevante bepalingen van richtlijn 1999/5/ EG. , jiddikjara li dan AirStation WZR-HP-G450H jikkonforma maltiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. nyilatkozom, hogy a AirStation WZR-HP-G450H megfelel a vonatkozó alapvetõ követelményeknek és az 1999/5/EC irányelv egyéb elõírásainak. [. . . ]