User manual BUFFALO WLE-HG-NDR

[. . . ] Gain Amount of wireless signal strength added to a standard signal normally measured in db 's. MC Card Connector - Antenna connector type used on Buffalo Technology routers/AP's, adapter and indoor antenna products. N type connector - Antenna connector type used on Buffalo Technology outdoor antenna's and coaxial cable. Omni-Directional Antenna - An Antenna that radiates a signal in a 360 degree radius horizontally and a signal vertically with a degree spread that is dependent on the antenna's elements. 3 Basic Antenna Information Wireless signals travel outward in an arc pattern from the source. [. . . ] See picture. Next wrap the vinyl taped connection with the electrical tape provided. These steps are to help ensure the connection stays stable and provide water proofing. Important thing to remember is to start tapping from the bottom up so that each layer is overlapping this will help keep water out of the connection see image. After you have wrapped the connection you slide the boot from the previous step over the taping. It should fit flush against the bottom of the connection base. 8 Connecting the Antenna WLE-HG-NDR / WLE-HG-NDC Now connect the N-male to MC-card pigtail adapter to the other end of the cable, as shown. Now connect the MC-Card connector to your Buffalo product. If you are connecting this antenna outside a building or enclosure and high on a pole you should include a Lightning protector like the one shown below. This device will connect between the antenna and the coaxial cable you will then proceed with the other steps as listed. 9 Antenna Mounting Brackets WLE-KG-VPA / WLE-KG-VPB When mounting an external antenna it is important to pay attention to the location you are installing it. Please be aware that small incremental changes in elevation either up, down or side to side can make significant changes in the signal quality. You should test mount all antennas to check their signal patterns before making their mounting permanent. WLE-KG-VPA WLE-KG-VPB 10 WLE-NDR Technical Specifications Polarization Method Connector Type Frequency Range VSWR Antenna Gain loss Range Goal Dimensions Weight Package Contents Increase in LOS 20%or more, 50% or more using both sides 164 X 73 X 65 mm 110 g AirStation Omni Antenna, Mounting Screws, Reference Card, Warranty Card, Manual Vertical Polarizations MC 2, 401 - 2, 484 MHz (1-11channel) 1. 5 or less with coaxial cable Total gain 2. 5 dbi or more, without the cable Antenna Range/Pattern Connect the antenna's MC card connector into the wireless device. When using the antenna on an adapter you can judge the signal strength by watching the bars on the client manager as you adjust the antenna. When used on a router/AP you can test it by placing a device with a wireless adapter at a low signal position and then move the antenna on the router/AP to see if the signal improves. 11 WLE-DA2 Technical Specifications Polarization Method Connector Type Frequency Range VSWR Antenna Gain Range Goal Dimensions Weight Package Contents Vertical Polarizations MC 2, 401 - 2, 484 MHz (1-11channel) 1. 5 or less with coaxial cable Total gain 4 dbi or more, including the cable loss Unobstructed =200% (400% or more using flatbed antennas on both sides) 100 X 100 X 17 mm 0. 3 g AirStation FlatBed Antenna, Mounting Screws, RP-TNC to MC card adapter, Reference Card, Warranty card, Manual Connect the antenna's MC card connector into the wireless device. When using the antenna on an adapter you can judge the signal strength by watching the bars on the client manager as you adjust the antenna. When used on a router/AP you can test it by placing a device with a wireless adapter at a low signal position and then move the antenna on the router/AP to see if the signal improves. Approximate Range 12 WLE-HG-NDR Technical Specifications Polarization Method Connector Type Frequency Range Antenna Gain Dimensions Weight Package Contents Vertical or Horizontal; Horizontal during transmission MC, external MC to RP-TNC connector included 2, 401 - 2, 484 MHz (1-11channel) 6. 5 dBi (4. 7 dBi including cable loss) 35 X 10. 5 X 10 cm 0. 22 kg , 0. 45 lb. 2. 4 GHz Indoor Omni Antenna with 5 foot cable, 2 Screws for wall mounting, MC to RP-TNC connector, Quick Setup Guide, Warranty Statement Connect the antenna's MC card connector into the wireless device. When using the antenna on an adapter you can judge the signal strength by watching the bars on the client manager as you adjust the antenna. When used on a router/AP you can test it by placing a device with a wireless adapter at a low signal position and then move the antenna on the router/AP to see if the signal improves. Approximate Range The AirStation 6. 5 dBi High Gain Indoor Omni Directional Antenna, model WLE-HG-NDR supports 2. 4 GHz 802. 11g and 802. 11b wireless devices to increase signal strength up to 2 times and boost wireless performance. MC to RP-TNC connector adapter is included for use with other manufacturers' wireless devices. The 5 ft. cable offers the option for desktop placement or wall mounting. Slick design, easy installation offers a perfect high gain antenna solution for any wireless network. Adjustment of antenna angle is recommended to improve the signal strength and boost performance. 13 WLE-MYG Technical Specifications Polarization Method Connector Type Frequency Range Antenna Gain Weight Dimensions Package Contents Vertical or Horizontal; Horizontal during transmission MC, external MC to RP-TNC connector included 2, 401 - 2, 484 MHz (1-11 Channels) 4. 5 dBi including cable loss 0. 77 kg 11. 6 x 3. 6 x 8. 1 cm WLE-MYG Antenna, MC to RP-TNC Connector Adapter with attached cable, Two Screws, Quick Setup Guide, Warranty Statement Connect the antenna's MC card connector into the wireless device. When using the antenna on an adapter you can judge the signal strength by watching the bars on the client manager as you adjust the antenna. [. . . ] be liable in any way to the user for damages, including any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use the Buffalo products. liability exceed the price paid for the product from direct, indirect, special, incidental, or consequential damages resulting from the use of the product, its accompanying software, or its documentation. does not offer refunds for any product. ©2004 Buffalo Technology (USA)Inc. 19 FCC FCC Compliance Statement - This device complies with Part 15 of the FCC Rules. [. . . ]