User manual BUFFALO WHR-HP-AG108

[. . . ] User Manual - AirStation WHR-HP-AG108 High Power Dual A + G Smart Wireless Router www. buffalotech. com v. The AirStation High Power Combo A + G Wireless Router provides two separate wireless networks at the same time, one on the 2. 4ghz 802. 11g frequency and another on the 5ghz 802. 11a frequency. System Requirements · A high-speed (Broadband) Internet connection or existing local area connection. · A computer with a network connection (wired or wireless) and a good web browser. The screenshots in this manual were taken with Firefox, but Netscape and Internet Explorer are also supported in versions 4. 5 or later, and Safari 1. 0 and later is supported with Macintosh OS X 10. 2 and later. AirStation WHR-HP-AG108 Package Contents · · · · · · · WHR-HP-AG108 Base Station Antenna AC adapter and power cable CAT5 LAN cable Utility CD with Manual Quick Setup Guides Warranty Statement Basic Setup Begin by finding a good place to set up your router/access point. [. . . ] If the ping returns "Connection failed" or other errors, something is preventing you from communicating successfully with your target. Connecting to a Preexisting Network Add an AirStation without changing your existing LAN configuration 1. Set the AirStation into Bridge/AP Mode by moving the switch on the bottom from AUTO to BRI. Connect one of the AirStation's LAN ports to an existing router or switch on your network. Open LAN Settings - LAN Port Settings and configure the following settings: IP Address =[192. 168. 11. 1] (Specify an unused network address from the existing LAN. ) Subnet Mask=[255. 255. 255. 0] (Use the same Subnet Mask as the existing LAN. ) DHCP Server Function=[Disable] 4. The PC used for configuration will need to be restarted before continuing configuration. Antenna The WHR-HP-AG108's external antenna will usually give the best performance if oriented to point straight up. If your AirStation is resting on its side, use the antenna's swivel and twist function to orient it pointed upward. Specifications For more information, FAQ's, and updates, consult the AirStation website at http://www. buffalotech. com. WHR-HP-AG108 AirStation Specifications Physical Specifications Dimensions 1. 1 x 5. 1 x 5. 7 in. (277g) Temperature & Humidity Operation 0° to 40° C Maximum humidity 80% Transit/Storage 0° to 40° C maximum humidity 80% (no condensation) Power Characteristics Transmit Mode 1. 1A (Nominal), Power Supply 5 V output; 100-240V AC Universal, 50/60 Hz Power Consumption about 6. 5 Watts (Max) 0 Specifications Regulatory Information Wireless communication is often subject to local radio regulations. Although AirStation wireless networking products have been designed for operation in the license-free 2. 4 GHz and 5GHz bands, local radio regulations may impose limitations on the use of wireless communication equipment. Network Compatability IEEE802. 11g/b/a Standard for Wireless LANs (108* SuperAG Mode also Available. ) Wi-Fi (Wireless Fidelity) certified by the Wi-Fi Alliance. Host Operating System Microsoft Windows® 98SE/ME/NT4. 0/2000/XP, Unix, Linux and MacOS Media Access Protocol Wired - CSMD/CD (Collision Detection) Wireless - CSMD/CA (Collision Avoidance) with Acknowledgment (ACK) 1 Troubleshooting Common Problems · · · · Out of range, client cannot connect to the AirStation. Conflict of another device with the AirStation hardware. LED Activity Monitoring LED activity helps identify problems. · Power LED should be Green, · Wireless LED should be Green if the line is active. · Ethernet LED should be Green (100Mbps) or Amber (10Mbps) while the communication is active. · The Red Diag LED will flash during boot and firmware updates. DIAG LED Activity Unplug the power for three seconds. Plug the power back in to monitor the Diag LEDs during start-up. Troubleshooting DIAG LED Activity Table DIAG LED Display Continuous Red Red flash, 3 times Red flash, 4 times Time Starting Starting Starting Description/Action RAM Error Red flash, 2 times Starting Flash ROM Error A problem on the wired LAN side A problem on the wireless LAN side LEDs Work But Client PC Cannot Connect to Network If the LEDs indicate that the network is working properly (Power LED is on, Transmit/ Receive LED blinks), check the TCP/IP settings of the network. Changing Client TCP/IP Settings in Windows Consult the LAN Administrator for correct TCP/IP settings. From the list of installed components, verify the TCP/IP => wireless LAN adapter protocol is installed. Troubleshooting · If the wireless adapter protocol is not yet installed, click the Add button and select the TCP/IP protocol from the list. · If the wireless adapter protocol is installed, select the protocol and click the Properties button. Verify that the parameters match the settings provided by your LAN Administrator. If prompted, restart your computer. Other Problems Please refer to www. buffalotech. com for further reference materials. Glossary 10BaseT: 802. 3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 100BaseT: 802. 3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 1000BaseT: 802. 3 based Ethernet network that uses UTP (Unshielded twisted pair) cable and a star topology. 802. 1x: The standard for wireless LAN authentication used between an AP and a client. [. . . ] Where it concerns radio equipment, such information shall be sufficient to identify on the packaging and the instructions for use of the apparatus the Member States or the geographical area within a Member State where the equipment is intended to be used and shall alert the user by the marking on the apparatus referred to in Annex VII, paragraph 5, to potential restrictions or requirements for authorization of use of the radio equipment in certain Member States. 1 Declaration of Conformity with Regard to the R&TTE Directive 1999/5/EC Cesky [Czech] Buffalo Technology Inc. tímto prohlasuje, ze tento AirStation WHR-HP-AG108 je ve shod se základními pozadavky a dalsími píslusnými ustanoveními smrnice 1999/5/ES. erklærer herved, at følgende udstyr AirStation WHR-HP-AG108 overholder de væsentlige krav og øvrige relevante krav i direktiv 1999/5/EF. dass sich das Gerät AirStation WHR-HP-AG108 in Übereinstimmung mit den grundlegenden Anforderungen und den übrigen einschlägigen Bestimmungen der Richtlinie 1999/5/EG befindet. [. . . ]