User manual BUFFALO WBR2-G54

[. . . ] User Manual 125 High Speed Mode* Wireless Cable/DSL Router WBR2-G54S www. buffalotech. com/wireless Table of Contents Introduction . 94 4 Introduction AirStation 125 High Speed Mode Wireless Cable/DSL Router (WBR2-G54S) This manual introduces you to the AirStation Cable/DSL Router, and will help you connect to your network quickly. The WBR2-G54S router, is a wireless 4-port router network device that complies with the 2. 4GHz IEEE 802. 11g standard specification on wireless LANs. The WBR2-G54S supports enhanced built-in NAT/SPI firewall functions and is used as a multi-functional router/link between wired and wireless LAN computers. [. . . ] · Prohibit setup via wireless bridge access point - Prohibits a personal computer connected to another AirStation in a wireless bridge. · Prohibit NBT and Microsoft-DS routing - Prevent unexpected external access via Microsoft network sharing. This prohibits computers on the internet from accessing shared resources on Windows machines. · Reject the IDENT request - The AirStation sends reject packets if it receives an IDENT request. 50 Advanced Settings Basic Filter Setting Use this filter when the communication speed goes down using a network application like E-mail, FTP and WEB. * If IDENT requests are forwarded to a LAN side client by address translation setting (DMZ or TCP port :113 ), this basic rule is ignored. 51 Advanced Settings IP Filter Settings - Limits the type of packets allowed to pass between the WAN and LAN. · Operation - Packets from WAN (or LAN), select ignored, rejected, or accepted. Packets from: IP Filter setting · WAN side - packets coming from the WAN side will be filtered. · Rejected - Return the rejected packet to the point of origin. Warning: If administrator selects packet from LAN is Ignored or Rejected, the administrator will 52 Advanced Settings no longer have access to the AirStation configuration screens. The AirStation can be returned to the factory default settings by holding down the INIT button on the back of the unit for five seconds or until the red DIAG light becomes solid. Select from all protocols, ICMP, arbitrary protocol number and TCP/UDP protocol number. · TCP/UDP Destination Port - Select TCP or UDP, then enter port number. The smaller the number, the higher the priority. Add MAC Filter setting MAC Filter - Click Enter MAC filter to enter MAC address. Source MAC address -The MAC address of the source of the packets that will be filtered may be set. Click Add rule when complete. 53 Advanced Settings Note: If configuring from a wireless computer, add your MAC address to the list of authorized wireless LAN PCs. Example: 00:40:26:00:11:22 Click Apply when settings are complete. 54 Advanced Settings Intrusion Detector Setup Intrusion Detector The Intrusion Detector watch guards and prevents unauthorized access from the WAN (Internet) This function also records information on unauthorized access attempts Intrusion Detector - Select Do not use, Use or Use (Apply Packet filter setting for Intrusion Detector setting). Threshold Value - Enter the number (1-999) of suspect packets before the notification occurs. Notify by email · Notification email address - Enter destination email address · Sender email address - Enter the email address that will send the email. This is the name that will appear as the sender when the email is read. DETECTOR@AIRSTATION 55 · Sender email server address - Enter the SMTP Server address. · Receiving email server authorization - Enter the POP3 Server address, User name and Password. This is only required if your SMTP server requires POP verification before it allows email to be sent. · Send test - Click Send to test notification; this will also save and commit the entries. [. . . ] If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures: -Reorient or relocate the receiving antenna. -Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. 91 FCC / CE Information FCC RF Radiation Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. [. . . ]