User manual BT DUET 450C

[. . . ] See page 10 Redial button Press to redial the last number called or to enter a pause in the memory. See page 9 Quickdial Enables two-touch dialling of up to 10 stored numbers. Memory label Hook switch Lets you make a follow-on call without replacing the handset. Night light switch Turns the night light on or off. AL light Comes on when the alarm has been set. Snooze Switches off the alarm to re-activate after approximately 9 minutes. [. . . ] There are three settings: HI Plug the attached 3 pin plug into the mains power socket A loud ring; your Duet 450 is preset to this position. LOW A quiet ring. OFF no ring Your Duet 450 is now ready for use 7 Using the Telephone 4 Press the STORE button. Storing and dialling numbers STORE To store phone numbers in the Quickdial memory 5 Press the memory Your Duet 450 Clock Telephone has three one-touch memory buttons M1, M2 or M3. You can store a further 10 telephone numbers in the two-touch Quickdial memory. To store a phone number in the onetouch memory button (M1, M2 or M3) under which you want to store the number. M1 1 Lift the handset. Replace the handset. To dial a number stored in the onetouch memory 2 Press the STORE button. STORE 3 Dial the number you want to store using the keypad. 4 Press the STORE button. 1 Lift the handset. STORE 5 Press the keypad 2 Press the one-touch 1 Lift the handset. memory button (M1, M2 or M3) you want to dial. M1 button (0-9) under which you want to store the number. JK 5 L 2 Press the STORE button. STORE The number is dialled automatically. One touch memory label Replace the handset. The number is stored. 3 Dial the number you want to store using the keypad. Use the label by the M1, M2 and M3 button to keep a record of the stored numbers. 8 To dial a number stored in the Quickdial memory To dial numbers longer than 16 digits To store a pause 1 Lift the handset. 1 Lift the handset. 1 Some switchboards 2 Press the QUICKDIAL 2 Dial the first 16 digits button. QUICKDIAL 3 Press the 0 -9 location under which the number you require is stored. JK by pressing the M1, M2, M3 or Quickdial button under which the second part of the number is stored. The whole number is stored automatically. can take a short time to pick up an outside line. You can insert a pause as required to allow for this delay. 2 Press the REDIAL 5 button at the required point when storing a number. The pause is stored in the memory. REDIAL The phone number is dialled automatically. Storing numbers longer than 16 digits Telephone numbers longer than 16 digits can be stored by entering the first 16 digits in one memory location, then storing the remaining digits under a second memory location. L To redial a number When dialling normally, pressing the REDIAL button will enter a pause in the number 1 Lift the handset. 2 Press the REDIAL button. REDIAL The last number called is redialled automatically. 9 Using the Secrecy button Using the R (Recall) button The secrecy button allows you to talk to someone whilst on a call, without the person at the other end of the line hearing your conversation. 1 During a call, press and hold down the SECRECY button. Your caller will not be able to hear you. SECRECY If your Duet 450 Clock Telephone is connected to a switchboard, the R button enables you to use the switchboards special features. Please contact your communications manager or switchboard supplier for further details. R 2 Release the SECRECY button to talk to your caller again. The R button is also used in connection with BT Select Services. For more information contact BT Free on 152 for residential customers or 154 for business customers 8am-6pm, Monday to Friday. Please note: If you are using the R button as part of a stored number, it must be followed by a pause. See `To store a pause' 10 Using the Clock To set the time To set the alarm To stop the alarm 1 Press and hold the CLOCK button. 2 Press the HOUR button When the alarm goes off: 1 Press the ALARM until the hour you want is displayed. 3 Press the MINUTE until the hour you want is displayed. 3 Press the MINUTE button to switch it off. The alarm will not sound again until the same time tomorrow. button until the right time is displayed. 4 Release the CLOCK button. The time is set. Please note: button until the time you want is displayed. If the alarm is set for after midday, the PM light comes on. 4 Turn the ALARM switch to ON. The To use the snooze button The PM light comes on when the clock time is set to midday or after. 1 Press the SNOOZE Alarm light comes on. AL The alarm will now go off at the time you have set. button when the alarm goes off. [. . . ] The brown wire must be connected to the terminal marked with the letter L or the word `Red'. No connection should be made to the Earth terminal marked with the letter E or coloured green or green and yellow, or marked by the safety earth symbol. If any other plug or connection is used, a 3 Amp fuse must be fitted to either the plug of the adaptor or in the distribution board. If in doubt, contact a qualified electrician. Safety Precautions 1 Do not allow your if it does not function properly. Disconnect the mains plug from the wall socket and consult your dealer. 6 Moisture condensation clock radio to become damp or wet. 2 Unplug from the - If your Clock Telephone is moved from a cold to a warm enviroment, water in the air will condense on some parts of the appliance and may cause damage or malfunction if the equipment is used. [. . . ]