User manual BRUNTON PED1202

[. . . ] 3 3. 1 3. 2 3. 3 3. 4 ----Position GPS Navigation Time / Date Barometer 3. 5 -- Altimeter 4 -- TrueMagneticTM Compass Function . . . . . . . . . 5 INSTRUCTIONS 6 -- 22 7 -- Settings & Side Functions . . . . . . . . . . . . . . . . . . . . . . . . 6 7. 1 7. 2 7. 3 7. 4 7. 5 7. 6 7. 7 -------More Settings Position Side Functions & Settings Altitude Side Functions & Settings Barometer Side Functions & Settings Time / Date Side Functions & Settings GPS Side Functions & Settings Compass Side Functions & Settings ii OWNER'S MANUAL TABLE OF CONTENTS 8 -- Waypoint Function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 8. 1 -- Waypoint Menu 8. 2 -- Route Menu 9 -- Maps & Reference Systems . . . . . . . . . . . . . . . . . . . . [. . . ] Use the following to help determine the values for your local time zone. Eastern Daylight Savings Time (DST): -4. 00 Central DST: -5. 00 Mountain DST: -6. 00 Pacific DST: -7. 00 Alaska DST: -8. 00 Hawaii DST: -9. 00 MORE SETTINGS Previously described in section 7. 1. 7. 6 -- GPS SIDE FUNCTIONS & SETTINGS 7. 6-1 SIDE FUNCTIONS There is one side function related to the GPS Navigation function. When no waypoint or *HOME* is selected the direction and speed of your travel is displayed. Eastern Standard Time (ST): -5. 00 Central ST: -6. 00 Mountain ST: -7. 00 Pacific ST: -8. 00 Alaska ST: -9. 00 Hawaii ST: -10. 00 ONLY When Waypoint or HOME is selected GPS Main Function 2. When a GOTO waypoint is selected the waypoint name is indicated on top of the screen with the bearing and distance below. 20) Waypoint name will cycle with time to go (TTG) and Cross Track Error (XTE), if you have selected to display Cross Track Error in section 7. 1-8. The segment and steering arrows will point towards the selected waypoint. The steering indicator, direction and speed of travel will be displayed if you are moving. To CANCEL the GOTO waypoint see section 7. 7-2. Figure 19 Navigation Side Function Figure 20 11 3. When *HOME* is selected in the StraightHome function, BACK is displayed just above *HOME*. 7. 7-2 SETTINGS There are seven possible settings related to the TrueMagnetic compass function. GOTO WAYPOINT Setting To select a waypoint to navigate towards press YES. Use UP and DOWN to scroll through waypoints in alphabetical order starting with the waypoint last entered. GOTO NAV STARTED will be displayed, and Multi-Navigator will return to the TrueMagnetic compass function. When desired waypoint is displayed press YES to confirm. 13 MAGNETIC VAR Setting Magnetic variation (declination) is the angle difference at your location between true geographic North and magnetic North (the direction all magnetic compasses point). It is important to note magnetic declination at your position, since magnetic declination varies and fluctuates slowly at different rates around the world. Most maps use geographic North as a reference and a magnetic compass points at magnetic North. It is therefore Figure 25 necessary to adjust the compass so the bearings correspond with the map. The Multi-Navigator has a built-in model to calculate the local magnetic declination automatically from the GPS position. If you are at all are unsure of the value of the magnetic variation we recommend you to select AUTO. If you select manual entry (MAN) you must enter the amount of declination in degrees and select either East or West. [. . . ] Visit http://www. brunton. com, to find supplementary information about this and other Brunton products. 22 APPENDICES Glossary Included below are words that are used quite frequently. Knowing the meaning of them will make your navigation more fun, and the use of the Multi-Navigator even easier. Global Positioning System (GPS) ­ GPS has more than 24 operating satellites around the Earth. Each satellite provides the precise timing used by the GPS receiver in the Multi-Navigator to calculate its position. [. . . ]