User manual BRITAX WEEKENDER 3 IN 1

[. . . ] KEEP THESE INSTRUCTIONS IN A SAFE PLACE FOR FUTURE REFERENCE. To prolong the life of your nursery product keep it clean and do not leave it in the direct sunlight for extended periods of time. Removable fabric covers and trims may be cleaned using warm water with a household soap or a mild detergent. Do not machine wash, tumble or spin dry, unless the care labelling on the product permits these methods. Non removable fabric covers and trims may be cleaned using a damp sponge with soap or mild detergent. [. . . ] Do not use this cot with a child who can climb out, weighs more than 15kg, or is taller than 90cms. The thickness of the mattress has been specified to ensure that the distance from the top of the mattress to the top of the lowest side or end will always be at least 500mm. Always check parts regularly for tightness of screws, nuts and other fasteners - tighten if required. Do not use an additional mattress, padding, toys or other objects in the cot which would help your child fall out. Using the wrong size mattress may create hazardous gaps that could result in suffocation or could reduce the side height of the cot, which may result in your child falling out of the cot. THIS PRODUCT IS NOT INTENDED FOR COMMERCIAL USE. 02 www. britax. com. au www. britax. com. au 11 NOTES WARNING - MATTRESS SIZE This cot is made for a mattress which is 740mm wide, 1000mm long and no more than 25mm thick. Using the wrong size mattress may create hazardous gaps that could result in suffocation or could reduce the side height of the cot which may result in your child falling out from the cot. For its correct use, ensure you follow these instructions in the order that they are written. PARTS LIST A B C D E F 1 - Carry bag 1 - Mattress 4 - Mattress Support Rods 1 - Cot 1 - Bassinette 1 - Change Table A B C D E F 10 www. britax. com. au www. britax. com. au 03 1. TO OPEN THE COT THESE STEPS WILL ENSURE THAT THE COT IS CORRECTLY OPENED AND READY FOR USE. Stand the cot on its feet and undo the hook & loop straps that hold the mattress around the frame. Starting with the short rails pull the centre up with both hands quickly until they are locked in place. 5. TO USE THE CHANGETABLE (con't) C D Pick the changetable up by the plastic hooks and connect to the Portable Cot short end rail as shown. Rotate the Changetable over the Portable Cot and engage each of the four clamps onto the side rails. Move the Bassinette clamps slightly if they interfere with attaching the Changetable. A C NOTE: MAKE SURE THE FOUR CLAMPS ARE ENGAGED ON TO THE SIDE RAILS. Attach the plastic clamps to the leg tubes to keep the pocket in place. When the Changetable is not in use, always fold over the end rail until required again. C (CAUTION: TAKE CARE, AS FINGER PINCHING CAN OCCUR IN THE CORNERS WHEN LOCKING THE RAILS IN PLACE. ) F Now do the same with the longer rails. G To remove the Changetable, release the plastic hooks from the top rails. THE CENTRE OF THE COT BASE MUST BE IN A RAISED POSITION TO ALLOW THE RAILS TO LOCK EASILY. G Holding one end of the cot clear of the ground, gently press down the handle in the middle of the base until the base lays down flat. The base should now be locked into position. E E G 04 www. britax. com. au www. britax. com. au 09 4. TO USE THE BASSINET (con't) D Snap the 12 plastic clips onto the top rails of the cot. Make sure the plastic clips are positioned against the edge of the corner mouldings. [. . . ] TO FOLD THE COT (con't) B C Pull the strap up in the middle of the base and then pull base up approximately 50cm. Release each top rail by lifting the rail slightly and squeezing on the buttons, located in the centre joint. TO USE THE BASSINET A Insert the 2, two-piece support rods into bassinet inner sleeves separately, then engage them in the middle by the locking pin. Insert the mattress and secure it to the bassinet by passing the loop straps through the slots in the bassinet base, then press the loop straps onto the hook padding, sewn to the underside of the bassinet. [. . . ]