User manual BRITAX STRIDER PLUS

[. . . ] Note: Second Seat, Bassinet, Infant Carrier and Footmuff are all sold separately. www. striderplus. com. au INDEX General Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Bassinet, Infant Carrier & Second Seat Warnings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] To secure the child in the harness, push buckles (A) through the buckle rings (B) and into the buckle housing (C) until the buckle prongs snap into position. Carefully adjust the harness by pulling the sliders (D) until the desired fit is achieved in the lap, shoulder and crotch straps. Always adjust the harness when changing the seating position of the child. To adjust harness height position, see section 16. 20 STROLLER ASSEMBLY & OPERATION 19. TETHER STRAP WARNING: Use the tether strap to prevent the Stroller from rolling away. NOTE: A tether strap is fitted to this Stroller, always place the loop over desired wrist when using the Stroller. A If the tether strap is removed, attach by looping over the handle, open one end of the tether strap and insert the opposite end through the opening created. Pull until tether strap tightens around handle. B Slide your hand through the tether strap whenever you use the Stroller. Hint: If tether strap is fitted in the centre of the handle, you can use it with either hand. C If you want to use the tether strap with the other hand, slow to a stop and apply the brake (see section 8). Slide your hand through the tether strap before unlocking brake. 20. TO FIT THE REVERSIBLE SEAT PAD NOTE: To assit with installing, release one side of the armbar, see item 12D and release the harness buckles. A Fit the reversible seat pad by sliding it under the harness and head pillow. Note: Locate wider part of pad towards the head. B Locate the reversible seat pad as shown. C The reverse side of the seat pad has a different fabric pattern. 21 STROLLER ASSEMBLY & OPERATION 21. TO USE THE REVERSIBLE SHOULDER PADS NOTE: The shoulder pads are reversible. A Fit the reversible shoulder pads by fitting around the harness shoulder strap and attach the hook and pile. B Repeat for the other reversible shoulder pad. C The reverse side of the shoulder pad has a different fabric pattern. To reverse, undo the hook and pile and reattach on the reverse side. 22. ADJUSTABLE LEG SUPPORT A To lower or raise leg support, press in and hold both left and right buttons. B While holding both left and right buttons, tilt leg support up or down to the desired position. 22 STROLLER ASSEMBLY & OPERATION 23. TO FIT THE BOOTCOVER A Raise the leg support to the horizontal position. Hook the bootcover support. B Pull the top of bootcover under the armbar and then back over the top. C Connect the press studs to keep in place. TO USE THE BASKET NOTE: When a child is in the Second Seat, basket access is recommended only from the sides, or from the front on 4 wheel models only. There is no front access to the basket on 3 wheel models. A Access is available from either side by undoing the zippers. B Access is available from the front by undoing the zipper on 4 wheel models only. C Access is available from the rear of the Stroller. 23 STROLLER ASSEMBLY & OPERATION 25. TO USE THE FOOTMUFF (PURCHASED SEPERATELY) NOTE: Always secure the harness through the strap holes before use. A To prepare the Stroller for fitment of the footmuff, firstly, ensure the head pillow height is correctly adjusted for your child, see section 16. Fold the canopy back, disengage one side of the armbar and rotate to the side of the frame, see section 12D. B Undo the buckle prongs from the buckle housing, then release the buckle rings from the buckle prongs. Remove the reversible seat pad & shoulder pads. C To fit the footmuff into the Stroller, first unzip the top section from the padded bottom section and set the top section aside. Place the padded bottom section into the Stroller seat. D Thread the harness through the slots in the footmuff. [. . . ] To release the buckle, squeeze the top and bottom buckle prongs (A). 41 SECOND SEAT ASSEMBLY & OPERATION 31. TO USE THE SECOND SEAT - CONTINUED 31. 5 Reversible shoulder pads NOTE: The shoulder pads are reversible. A Fit the reversible shoulder pads by fitting around the harness shoulder strap and attach the hook and pile. B Repeat for the other reversible shoulder pad. C The reverse side of the shoulder pad has a different fabric pattern. To reverse, undo the hook and pile and reattach on the reverse side. 31. 6 To adjust the head pillow and harness shoulder strap height position A The head pillow has a small height adjusting range. Attach to the best suited hook and pile position as required. B The harness straps are threaded through the head pillow so the shoulder strap height is adjusted when the head pillow height is adjusted. 42 SECOND SEAT ASSEMBLY & OPERATION 31. [. . . ]