User manual BRITAX PARKWAY

[. . . ] However, correctly installed, a booster seat will substantially improve the chances for survival in most crashes. Make sure that all users fully understand the correct ways to use this booster seat in a vehicle. · Do not, except as described in this book, attempt to disassemble or modify any part of the booster seat or vehicle belts. In the event of a sudden stop, loose objects will keep moving, potentially causing serious injuries. [. . . ] The following types of vehicle belts are not compatible with this booster seat: Two-point belts of any kind. Three-point belts that have separate retractors for the shoulder section and the lap section. The vehicle owner's manual will have information on the types of seat belts in the vehicle. If the belt type is listed above, select another seating position. Vehicle Seating Positions WARNING!Department of Transportation warn that children 12 and under must ride in the rear seats, away from front air bags. When using in vehicle with air bags, refer to the vehicle owner's manual for additional booster seat installation instructions and precautions. · Forward facing vehicle seats MUST be used with this booster seat. Side facing or rear facing seats in vans, station wagons or trucks CANNOT be used. 6 7 Features Installation 1 2 3 4 5 Securing the Child 1 Place the booster seat in a vehicle seating position equipped with a lapshoulder belt. · Refer to pages 6­7 to determine the best seating position for the child. · Position the booster seat with the back against the vehicle seat. Adjust recline, if necessary, for proper fit. 3 6 5 7 4 2 Position lap portion of the vehicle belt over child's upper thighs and both base belt guides, then buckle (fig. 3 Position the shoulder portion of the vehicle belt through the headrest beltguide, opposite the buckle (fig. B). · Shoulder belt must be positioned so it rests on the child's shoulder. · Procedure continued on page 10. A B 1 2 3 4 5 6 7 8 Headrest Adjust Handle Headrest Headrest Belt Guide Backrest Base Belt Guide Cup/Snack Holder Base Adjustable Recline 8 7 5 6 8 9 Securing the Child Installation (continued from page 9) 4 Remove slack from lap, then shoulder portion of the vehicle belt to provide a comfortable but snug fit for the child (fig. C Adjustments Adjusting Headrest Height Use the multi-position headrest to adjust the height of the booster seat. 1 Check the current fit with the child seated in the booster seat. · Make note of the adjustment needed for a fit where the beltguides are even with or just above the child's shoulders. E 2 Squeeze the handle to release headrest lock (fig. 4 Release handle to lock position of headrest. D 10 11 Care and Maintenance Cover Removal TIP: Use a blunt rod or tweezers to assist with tucking and untucking the cover from hooks in the shell. 7 6 7 6 Care and Maintenance 2 Hook elastic loops (2x) to attachment points on bottom rear of headrest (fig. 4 Route each elastic from bottom of headrest cover in front of backrest, then through the slot to the rear of the booster seat and hook elastic loop to attachment point on rear of base (2x) (fig. 5 Tuck adjacent fabric behind attachment points (4x) on sides of headrest at rear of booster seat (fig. To refit base/backrest cover: 6 Fit seat section of cover over base, then thread elastic loops through slots between the base and backrest. 7 Fasten hooks (2x) to opposite side elastic loops at rear of booster seat (fig. [. . . ] TOWEL DRY DO NOT: Use solvents, abrasive cleaners, or disassemble booster seat in any way, except as instructed. 13 Warranty This booster seat was manufactured by Britax. ("Britax") warrants this product to the original retail purchaser as follows: LIMITED WARRANTY This booster seat is warranted against defective materials or workmanship for one year from the date of original purchase. The exclusive remedy for this warranty is that Britax will, at its option, provide repair or replacement components for this product or refund the original purchase price of the product. Britax reserves the right to discontinue or change fabrics, parts, models or products, or to make substitutions. [. . . ]