User manual BRITAX BABY SAFE

[. . . ] 36 This product and its components are subject to change without notice. BB0-627-00 / P241000 R1:09/04 · Use only in a rear facing position when using this restraint in the vehicle. · Use only with children who weigh between 4 and 22 pounds (2 and 10 kg) and whose height is 30 inches (76 cm) or less. · Snugly adjust the belts provided with this restraint around your child. [. . . ] Doing so will reduce the stability of the base. Basic Base Functions Using Carrier with Base To attach, line up carrier with base, rear facing, then push down until positive click confirms correct attachment (fig. Check installation by lifting carrier from both ends to verify that both attachment rods are engaged with the base. Visual confirmation can be made, using the button indicator on the rear of the base D (fig. When carrier is attached properly, the green indicator band on the release button is fully visible (fig. E). Adjust foot prop height by pressing Foot Prop Adjust Button while sliding foot prop to the shortest position that provides contact with the vehicle floor (fig. To store foot prop for transport outside of the vehicle, adjust to shortest position, then B collapse into Storage Mode (fig. Press tab into slot on bottom of base to secure. 1 2 To release, press release button on base, then lift carrier to remove (fig. F). IMPORTANT: Always adjust handle to InVehicle position while using in a vehicle. E Indicator C 20 E 21 Base Installation ISOFIX Installation · Figure A illustrates a typical base ISOFIX installation. If ISOFIX anchors are not available, you must use vehicle belt installation methods. Base Installation 5 Adjust foot prop so that it is against the vehicle floor. WARNING: Never use foot prop to raise base above vehicle seat surface. Doing so will reduce the stability of the base. 6 Attach carrier to base. 1 Place ISOFIX connectors in ISOFIX A Installation Mode. · Remove ISOFIX Protective Cap and spacers, if installed. · Always use foot prop when base is 2 Place foot prop in Installation Mode. installed in vehicle! · Verify that the green indicator band on the release button is fully visible. · Verify that the red line on carrier is level D with the ground. · If angle is not correct, remove carrier and base, then adjust recline angle as directed on page 19. Indicator 3 Line up ISOFIX connectors on base with anchors in vehicle (fig. B). 7 Adjust carrier handle to In-Vehicle position. Removal Squeeze green and red ISOFIX release buttons on each connector (fig. D), then D pull base away from vehicle seat. IMPORTANT: Always store ISOFIX connectors when not in use. See page 18. · If it is difficult to line up ISOFIX connectors with ISOFIX anchors, use Insertion Aid for assistance, as instructed B on page 23. 4 Engage ISOFIX connectors by pressing base onto ISOFIX anchors, until a positive click is heard (fig. C). ISOFIX Guides If necessary, use ISOFIX Guides to assist with base attachment to ISOFIX anchors. To use, clip ISOFIX Guide onto each ISOFIX connector that will be used for installation of base (Fig. E). · Visual confirmation can be made using the green ISOFIX indicators. Green indicator must be fully visible from the side when installed properly (fig. · Pull base away from vehicle seat to further verify attachment. ISOFIX Guide C E 23 22 Base Installation Lap-Shoulder Belt Installation · Figure A illustrates a typical base lapshoulder belt installation. [. . . ] 2 Pull buckle away from carrier until B Buckle Retainer tight, then verify that the strap is not twisted and the release button is facing outward. IMPORTANT: Verify that retainer is threaded through both the cover AND the shell. 32 33 Care and Maintenance Cover Removal 1 Unhook attachment loops. 3 From the bottom of the carrier, unhook both harness straps from the yoke. 4 From the top of the carrier, pull each harness strap through the upper harness slot, head support pillow and cover slot to the top of the carrier. 6 Pull the harness straps, buckle tongues, and chest clip through the slots in the cover. [. . . ]