User manual BRITAX B-READY

[. . . ] B-READYTM Stroller User Guide IMPORTANT: To ensure your child is as safe as possible, read all instructions thoroughly before using this stroller. Store this manual for future reference. Table of Contents Warnings. [. . . ] · To avoid entrapment or pinching, do not fold or unfold stroller when child is in or near stroller. · Only use accessories and replacement parts approved by Britax Child Safety, Inc. · Read and understand these instructions before using this product. To ensure proper use, store this user guide in a convenient place so it can be consulted often. Failure to follow all warnings and instructions could result in serious injury or death. · When using an infant car seat with this product, refer to the product's user guide for maximum weights and other instructions. · Do not exceed the manufacturer's maximum weight limit when using an infant car seat with this product. 3 Features Canopy Arm. Bar Harness Buckle Chassis. Lever Seat. Locking. Latch Chassis. Socket Release. Lever Storage. Pouch Leg. Rest Front. Wheel. Basket 4 · Actual product may vary from images. In the Box Front. Wheels. x2 Rear. Wheels. x2 Main. Seat Arm. Bar Cup. Holder Mud. Guards. x2 Storage. Pouch Stroller. Frame Britax. Infant. Car. seat. Adapters Rain. Cover 5 Assembly Unfolding · Lift chassis lock lever and open the frame · Lift handle until frame locks into upright position as shown Front Wheels · Slide mounting pins into the housing on the frame until they lock into place NOTE: The Britax logo imprinted on the wheel should be facing the outside of the stroller 6 Assembly Mud Guards · Slide the mud guard onto the mounting bracket above each rear wheel housing until it locks into place Rear Wheel Housing Rear Wheels NOTE: Left and right wheels are marked with an L or R and are from the perspective of standing behind the stroller · Hold in the release button in the center of the wheel and slide the mounting pin into the housing on the rear axle 7 Assembly Storage Pouch · Slide the hook and loop fasteners on both sides of the pouch through the tabs above each back wheel · Attach hook and loop strip to the strip on the inside of the under seat basket Arm Bar · Attaching: slide the pins into the mounts on the seat until they lock into place · Removing: push the release button on the bottom of the mounts and pull arm bar out NOTE: Armbar or cup holders must always be used to avoid finger entrapment in the open connectors 8 Assembly Cup Holder · Line up the arrow with the pin just below the folding release lever and snap the cup holder mount onto the frame Removing Front Wheels · To remove, rotate the cap in the direction indicated by the arrows until wheel releases Removing Rear Wheels · Press and hold the release button in the center of the wheel and pull away from the wheel housing 9 Operating Instructions Parking Brake · Step on the brake pedal until the indicator window changes color Red indicates the brake is engaged and green indicates the brake is off Attaching the Seat · Insert the seat locking latches into both chassis sockets · Push down until an audible click is heard NOTE: Seat attaches forward or rear facing 10 Operating Instructions · Pull up on the seat to ensure that it is locked into place correctly Detaching the Seat IMPORTANT: Always remove child before detaching the seat · Lift both release levers on each seat locking latch at the same time · Lift upward 11 Operating Instructions Folding Always apply brake and remove children before folding the stroller · Pull up both frame release levers located just below the stroller handle, and step back while guiding stroller downward · Continue folding until the chassis lock engages TIP: You may need to compress the frame to engage the chassis lock Swivel Wheels · Toggle the wheel lock on the back of the front wheel housing up or down. Down will lock wheels forward and up will allow wheels to swivel 12 Operating Instructions Leg Rest · Depress buttons on both sides of the leg rest hinge and hold while raising or lowering the leg rest to the desired position Recline · Lift and hold the recline lever on the back of the seat and hold while raising or lowering the seat back to the desired position Handle Angle · Depress and hold the two release buttons on the inside of the handle assembly while raising or lowering the handle to the desired position 13 Securing Your Child · Release the harness by depressing the button in the center of the buckle while pulling the two top tongues away from the buckle assembly · Sit child in seat and unzip the seat back to access the harness height adjuster TIP: You may need to loosen the harness to adjust the harness height. · Squeeze the adjuster to release and slide up or down to one of the three positions NOTE: Adjusted harness height should be at or above the shoulders of the child 14 Securing Your Child · Buckle the harness by pressing the tongues on the harness straps into the buckle assembly NOTE: Ensure the straps are not twisted as they may become uncomfortable for the child · Tighten or loosen the harness straps by sliding the harness adjusters Buckle tongues separate for added safety. [. . . ] Neither Britax, nor the retailer selling this product, authorizes any person to create for it any other warranty, obligation, or liability in connection with this product . 26 Notes 27 Notes 28 Visit. our. website. at. www . Britax . com. for. more. information . Britax Child Safety, Inc. 13501 South Ridge Drive Charlotte, NC 28273 USA A Britax Childcare Group Limited company Tel. [. . . ]