User manual BRIO BH 200

[. . . ] While BH-200 is charging, When the headset is fully charged, Status LED is off. Unplug the charger from the head- tion (see callout 5). the Status LED is red. set and the wall outlet. Do not leave a fully charged battery connected to the charger. Switching The Headset On / Off 3 4 Front Back 9 2 1. Rejects an incoming call when pressed two times. Headset is switched on, but is not paired or does not have an active connection with a phone (connectable) Headset and phone are connected (connection active) Headset is waiting to be paired with a phone (ready for pairing) Incoming call Call ended Headset connected to charger and charging not complete Headset connected to charger and charging complete Battery charge level is low To switch on, press and hold the Power / Call Button for 2 seconds. [. . . ] When connected, BH-200 beeps once and the Status LED double flashes blue every 8 seconds. BH-200 is ready to be used with your phone. Number called is busy N/A Erasing Information For All Paired Phones Switch BH-200 on while your Bluetooth phone is off. BH-200's status should be Connectable (LED flashes blue every 5 seconds). The beep confirms that pairing information for all phones has been erased. Answering / Ending A Call ­ When receiving a call, the ring tone is heard through the headset speaker. To answer a call, briefly press the Power / Call Button on BH-200 or the answer key on your phone. If you do not want to answer the call, press the Power / Call Button two times. To end a call, briefly press the Power / Call Button on BH-200 or the end key on your phone. Adjusting The Headset Speaker Volume ­ Press the Volume Up Button to increase audio level or the Volume Down Button to decrease audio level. Switching A Call Between Headset / Phone ­ During the call, press the Power / Call Button and Volume Down Button simultaneously for 2 seconds, or use the respective function in your phone. Switching Between A Current / Waiting Call ­ To switch from your current call in progress to a waiting call, press and hold the Volume Up Button for about 2 seconds, or use the respective function in your phone. Muting The Microphone ­ To mute or unmute the microphone during a call, press and hold the Power / Call Button and Volume Up Button simultaneously for 2 seconds. A beep is provided every 5 seconds to advise that the microphone has been muted. Troubleshooting If the headset is not functioning, it may be necessary to reset BH-200. To reset the headset, press and hold the Volume Up Button and connect the QTC-BH200 charger to the headset. Once the QTC-BH200 is connected, continue to hold the Volume Up Button for 2 seconds to complete the reset. If you cannot connect BH-200 to your phone, make sure the headset is charged, switched on, and paired to a Bluetooth enabled phone. Also, ensure that the Bluetooth feature is activated on your phone, that the headset and phone are in close proximity (maximum 30 feet without obstruction), and that there is no interference from other electronic devices. Disconnecting Headset From A Phone The headset can be disconnected from your phone by: Using the Power Button to switch off BH-200. Moving BH-200 more than 30' away from your phone. Note: You do not need to delete the pairing to disconnect the headset from your phone. Headset Care Reconnecting Headset To A Paired Phone Use and store the BRIO BH-200 at room temperature and in dust / dirt free environments. Clean only with a damp cloth and mild detergent. Switch on BH-200 within 30' of your (last connected) phone and it will connect automatically. Your phone must also be switched on and its Bluetooth function enabled. If BH-200 does not connect automatically, check to make sure the headset and phone are paired. If BH-200 is moved more than 30' from the phone, the headset is out of range and will disconnect from the phone. A warning beep is provided when the headset moves out of range of the phone. [. . . ] For service under warranty, return the product along with dated proof of purchase to the retailer where purchased or to HT Mobile Products. If returning directly to HT Mobile Products, follow these instructions: 1. Send to HT Mobile Products ­ Warranty Service Department, 2170 Brandon Trail, Alpharetta, GA 30004. For your protection, we recommend you obtain proof of delivery for your shipment. [. . . ]