User manual BRAUN KM 32 B SERVICE DOCUMENTATION

[. . . ] No. 1 2 3 4 5 6 7 8 9 10 11 12 12a 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28a 28 29 30 31 32 33 34 35 36 37 38 39 40 Part Number 4207100 4207923 4207199 0033120 4207131 0003302 4209875 0001500 4207500 4209003 4390264 4206149 4203051 0003170 4216193 0717253 0002706 0612717 0622099 NLA 4230051 4230005 NLA 4243054 0034115 4230002 4207534 4230006 0108111 0003135 0028101 0102102 4230550 0030112 4250806 4230846 4250016 4250017 4230847 4250070 NLA NLA 4209 - 3 BINC Rev: 7/96 BAG Rev: 12/88 Service Documentation Spare Parts List 4209 Part Description Carbon brush Fixing clamp Lower end shield Centering rubber Capacitor Ferrite-tube Insulating tube Plug junction Double plug junction Wiring (w/ 1 slip on terminal) Wiring (w/ 2 slip on terminals) Type plate Accessories Large mixing bowl Small mixing bowl Dough hook Whisk Whisk for whipped cream Circlip for whisk/hook Spatula Dust cover 4203014 4207055 4207814 4207048 4207620 4207530 4203118 4203200 Pos. No. 41 42 43 44 45 46 - Part Number 4250048 4250047 4243817 4250045 NLA 4243078 NLA 0710127 NLA NLA NLA NLA For additional attachment parts see page 16 4209 - 4 BINC Rev: 7/96 BAG Rev: 7/84 Service Documentation Reference Drawing 4209 Bottom of the product 4209 - 5 BINC Rev: 7/96 BAG Rev: 12/88 Service Documentation Service Information 4209 Technical Data Voltage/Frequency: No-load power Position 1: Position 2: Position 3/L: No load speed Position 1: Position 2: Position 3/L: Overheating protection: Length of mains lead: Operating time: 110 V/120 V 40-60 Hz appr. 1. 30 m continuous operation at 400W 4209 - 6 BINC Rev: 7/96 BAG Rev: 7/84 Service Documentation Service Information 4209 1. [. . . ] Before starting to dismantle the motor, mark the latter in the longitudinal direction, so that all parts are again placed correctly left to right during the assembly. Before the motor is taken apart, first remove the carbon brushes (41). Prior to removing the brushes, loosen the fixing clips (42) at the sides and withdraw carefully. Carry out a functional test 4209 - 7 BINC Rev: 7/96 BAG Rev: 7/84 Service Documentation Reference Drawing 4209 Wiring with thermo-switch 4209 - 8 BINC Rev: 7/96 BAG Rev: 7/84 Service Documentation Reference Drawing 4209 Wiring diagram 4209 - 9 BINC Rev: 7/96 BAG Rev: 10/88 Service Documentation Reference Drawing 4209 Wiring diagram 4209 - 10 BINC Rev: 7/96 BAG Rev: 11/85 Service Documentation Service Information 4209 Products which are considered to be too loud or are returned for this defect. When judging the operating noise, the mixing arm of KM 32/B or the mixer attachment of the MX 32/B should be engaged. If the operating noise is still considered to be too loud, the following measures should be taken: 1. The motor should not have any off-center condition that means, the outside diameter of the male drive coupling (Pos. 1 must coincide with the inside diameter of the raised attachment cone shoulder (observe an even gap!). 26 respectively 37), must be checked for areas of breakage or other defects if necessary the parts must be exchanged. 58 and attach, if necessary, the new and Changed base plate (see instructions below). Instructions for Braun kitchen machine KM 32/B (4209) and Braun multimix MX 32/B (4142) From production week 45, 1985 on, the lower four rubber buffers (Pos. 38) of the motor suspension (plastic-type), will be eliminated without a replacement. In previously produced products, the rubber buffers should continue to be used. At the same time, also the previously used centering rubber parts (Pos. That means the holes to accept the centering rubber parts in the base plate, have been eliminated. For replacement of these parts, ribs have been molded in the same spot. [. . . ] No. Gear Head for Meat Mincer 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 Cover Cheese-head screw Split lock washer Upper gear housing cover Plain seal Steel washer Worm drive shaft Fiber washer Gear wheel Fiber washer Intermediate gear Plain seat Gear shaft Split lock washer Cheese head screw Winged screw Retainer ring Bronze washer Fiber washer Straight pin Shaft Seal-ring Lower housing Seal-ring Washer Coupling 4241020 0003101 0101001 4240803 4240012 4240021 4240003 4213040 4240008 4240004 4240022 4240025 4240807 NLA NLA 4241003 0109003 4241014 4241015 0120101 4240009 0104001 4240801 0712001 4213042 4203055 4209 - 20 BINC Rev: 7/96 BAG Rev: 2/95 Service Documentation Spare Parts List 4610 Part Description Part Number Pos. No. Meat Mincer attachment 1 2 3 4 5 5 6 6 7 7 7 8 Tamper Meat tray Housing Worm screw Spring Spring Cross shaped blade ** Cross shaped blade Perforated disc, 4. 5 dia. Locking ring 4242 040 4241004 4240811 4240045 4242148 4242148 4242133 4240048 4 195090 4 195091 4195092 4240050 ** Two sided applicable 4209 - 21 BINC Rev: 7/96 BAG Rev: 1/82 Service Documentation Exploded Drawing 4612 4209 - 22 BINC Rev: 7/96 BAG Rev: 10/86 Service Documentation Spare Parts List 4612 Part Description Reamer cone Strainer Juice container Adapter for KS 33 Pos. [. . . ]