User manual BOSTON ACOUSTICS VR-M90
DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual BOSTON ACOUSTICS VR-M90. We hope that this BOSTON ACOUSTICS VR-M90 user guide will be useful to you.
Manual abstract: user guide BOSTON ACOUSTICS VR-M90
Detailed instructions for use are in the User's Guide.
[. . . ] High frequencies are handled by Boston's patented 1-inch (25mm) aluminum tweeter with Amplitude Modification DeviceTM (AMD). This remarkable driver produces an extremely smooth, flat response well beyond the audible range. A die-cast, multi-finned aluminum heatsink attached to the tweeter's backplate dissipates heat quickly and efficiently, assuring cool, trouble-free operation, even at very high power levels. [. . . ] Insert the wire in the hole and tighten.
Checking the Speaker Connections
It is important that your speakers are hooked up with similar polarity or "in phase. " A simple listening test will tell you if your speakers are connected properly. While listening to music with your amplifier set to MONO, reverse the connections at one speaker only. The connection that yields the fuller bass and louder sound is correct.
3
VRM80/90 manual v3
11/28/01
12:58 PM
Page 4
Connecting the VR-M80 or VR-M90 to Your Amplifier or Receiver
Basic Hookup
1. Make sure the speaker terminal jumper straps are in place on the back of the speaker. When making all connections, be sure to connect + to + (red) and to (black).
speaker terminal with jumper strap in place
amplifier or receiver
Bi-wiring
Bi-wiring increases the flow of current and decreases intermodulation of different frequencies by providing separate inputs to the woofer and midrange/tweeter sections. Bi-wiring will usually improve the sound quality, although the improvement may be quite subtle. If you choose to bi-wire, use the same type and length of wire for all connections. When making all connections, be sure to connect + to + (red) and to (black).
1. Connect the wires from the amplifier's speaker terminals to each individual set of terminals on the back of the speaker as shown.
amplifier or receiver
4
VRM80/90 manual v3
11/28/01
12:58 PM
Page 5
Bi-amplification
Bi-amplification requires using separate amplifiers dedicated to high and low frequencies. Using more than one amplifier can enhance the dynamic performance of your system. "Splitting the load" between two amplifiers lets each amplifier work less hard, increasing the available current to the drive units. When making all connections, be sure to connect + to + (red) and to (black). Unscrew the terminal collars of both sets of terminals and remove the connector straps. Connect the wires from the bottom set of terminals to the amplifier driving the woofers. Connect the wires from the top set of terminals to the amplifier driving the midrange/tweeter.
right speaker
left speaker
low frequency amplifier
high frequency amplifier
CAUTION: Do not use an external active crossover with your VR-M speakers. The external crossover and the VR-M's internal crossover can interact and distort the phase and frequency response of the system.
Speaker Cable
You should always use high quality speaker cable for optimum audio results. [. . . ] If you listen in taller chairs or sofas or prefer to stand a lot or move about the room, then you may want to rake the speaker slightly backward. Refer to the diagram below on how to change the height or projection angle of your speakers using the rubber capped feet. The process is the same using the spikes except there is no hex nut, thus the included wrench will not be used. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE BOSTON ACOUSTICS VR-M90
Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual BOSTON ACOUSTICS VR-M90 will begin.