User manual BOSS RDS-3130MP3

[. . . ] Do not use second-hand or rental CDs that have a sticky residue on the surface (for example, from peeled-off stickers or from ink, or glue leaking from under the stickers). There are paste residue. Ink is sticky (P . 5). ******* **** ******* ******* ******* P1 . Do not stick paper or tape on the disc (P P5 . Do not use rental CDs with old labels that are beginning to peel off. Stickers that are beginning to peel away, leaving a sticky residue (P . 6). Do not expose the discs to direct sunlight or heat sources such as hot air-ducts, or leave them in a car parked in direct sunlight where there can be a considerable rise in temperature inside the car (P . 3). Do not use your CDs with labels or stickers attached. Labels are attached (P . 7). ******* ******* ******* ******* ******* P7 . [. . . ] Press this button shortly again, it will switch to changing color on display. 16) SOURCE BUTTON (SOURCE) Press this button to select Radio and CDP modes. The available selections depends on version: Radio CD Player Radio > CDP > AUX in Sub-woofer On/Off Press SOURCE button for more than 3 seconds to activate or turn off the Sub-woofer output. Aux Input Connect the external signal to the auxiliary line in jack located at the rear of the unit , then press Source button to select Aux mode. Press Source Button again to cancel Aux Mode and return to previous mode. RESET BUTTON The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a ballpoint pen or metal object will activate it. The reset button is to be activated for the following reasons: RE SE T Initial installation of the unit when all wiring is completed. Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. E-8 8. AUDIO OPERATIONS 10) ENCODER VOLUME BUTTON Turn this knob to adjust desired volume level. 5) AUDIO BUTTON Press this button to select desired audio function. ORDER OF FUNCTION: VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD) While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds, otherwise the unit will return to volume adjustment mode. 17) PRESET EQUALIZER BUTTON (EQ) Press this button to toggle the following EQ settings: FLAT->CLASSICS->POP M->ROCK M->DSP OFF At DSP OFF mode, EQ will be controlled by Bass/Treble setting. - When TP station is received, TP segment is turned on in LCD display. - TP (Traffic Program) If the tuned program carries Traffic Announcement, the TP indicator will turn on. - TA (Traffic Announcement) When an actual traffic bulletin is on air, the TA indicator will also turn on. E - 11 - PTY (Program Type Codes) This code is used to designate the current program material being broadcast. With this feature, you can search the programs that match the selected program type, which is chosen from a specific list of types. - EON (Enhanced Other Networks Information) It is a supplementary service enabling the radio to obtain information not only from the current station but also from the others. - CT (Clock Time) This function permits to update the clock of the receiver the nation from which the station is broadcasting (from PI). It could happen that on the display will be shown the wrong hour; this happens because in Italy the Clock Time function is not working yet. Notes Depending on the country or region, not all of the RDS functions are available in Italy. RDS may not work properly if the signal strength is weak or if the station you are tuned to is not transmitting RDS data. PROGRAMMABLE OPTIONALS To use this function press SEL Button for few seconds, each time you press this button the mode will move and the functions will shown on the display, turn the volume knob to set the desires functions , the function states as following: - TA SEEK, TA ALARM To determine what action will the radio take if the newly tuned station does not receive TP information for 5 seconds. TA SEEK The radio retunes to a different station which contains TP information. PI SOUND, PI MUTE When the vehicle is crossing the area where two stations with same AF but different PI code can be received at the same time, the receiver will become unstable, under this situation two modes can be selected. [. . . ] The unit searches files and directories which have the same character which is inputted by the user. The unit shows these sorted files and directories by TUNE UP / DOWN Button (TUNE DOWN First). If the selected name is directory, the user can go into the selected directory by press MP3 ENTER BUTTON and continue to search the directory or file name in the directory by TUNE UP / DOWN Button (TUNE DOWN First). The selected file can be played by pressing MP3 Enter Button The distribution of alphabetical characters are listed as follow : Button Character M1 M2 M3 M4 M5 M6 SUB SOURCE TUNE DN TUNE UP ID3 DISPLAY SEL VOL UP/DN A, B, C D, E, F G, H, I J, K, L M, N, O P , Q, R S, T, U V, W, X Y, Z, Space _, -, + Move Cursor Next/Previous Character E - 14 (2) SEARCH DIRECTORY / TRACK NAME BY USING ENCODER VOLUME KNOB Under MP3 Play Mode, press MP3 MENU BUTTON twice, the display shows " * ". [. . . ]