User manual BOSS OUTLAW LAC128D

[. . . ] Use only the parts included with the unit to ensure proper installation. Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle. Install the unit where it does not get in the driver's way and cannot injure the passenger if there is a sudden stop, like an emergency stop. If installation angle exceeds 30°° from horizontal, the unit might not give its optimum performance. [. . . ] (When re-attaching the frame, point the side with a groove down wards and attach it. ) c. Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. Trim Plate Installation: Push the trim plate against the chassis until it is fitted. You must do this before you install the front panel, otherwise it can't be attached. DIN REAR-MOUNT (METHOD B) Installation using the screw holes on the sides of the unit. Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned (are fitted) and tighten the screws at 2 places on each side. Hook (Remove this part) Note: the mounting box, outer trim ring, and half-sleeve are not used for method B installation. 2 4 3 2 5 5 E-4 4. DETACHABLE CONTROL PANEL (D. C. P . ) Removing The Detachable Control Panel (D. C. P . ). 1. Remove the D. C. P . PANEL RELEASE BUTTON Attaching the DCP 2 A B 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D. C. P (As shown on the digram). unit until a "click" sound is heard. CAUTION DO NOT insert the D. C. P from the left side. 17) PRESET EQUALIZER BUTTON (EQ) Press this button to toggle the following EQ settings: FLAT->CLASSICS->POP M->ROCK M->DSP OFF At DSP OFF mode, EQ will be controlled by Bass/Treble setting. 13) BAND/LOUDNESS BUTTON (BAND/LOUD) Press the Band/Loudness Button for couple of seconds to switch the loudness on or off. When Loudness is on, display will show 'Loud On' for a few seconds. E-9 9. RADIO OPERATIONS 11) AUTO MEMORY STORE/PRESET SCAN BUTTON (AS/PS) 1. PRESET SCAN: Press AS/PS button briefly to enter Preset Scan mode, it will scan all the preset stations in the memories, you can hear that it will stay on each station for about 5 seconds. 2. AUTO MEMORY STORE: Press AS/PS button for couple of seconds to enter Auto Store mode, this feature will automatically scan the current band and enter up to 6 strongest stations into the 6 preset memories. 7) STATION PRESET BUTTONS (M1-M6) 1. Press these buttons briefly to recall the stored stations in the selected band. 2. Presetting stations manually, Press the BAND button to select the band for the stations to be preset. Press the Preset button at which you want to store the station for at least 2 second. The preset number will appear on the display accompanied by a beep, this indicated that the station has been stored into memory. Press this button shortly to change between BAND FM1, FM2, FM3 or AM/MW bands. Press this button for couple of seconds to turn Loudness function on or off. [. . . ] 8) MONO STEREO BUTTON (MO/ST) When you receive a station, "ST" on the display will be on. 9) SCAN BUTTON(SCAN) Press this button, the radio will tune up to search stations, the available stations will blink and stay on the display for a few seconds. During station tuning, this button allows you prior to access strong local station only (Local mode), or to access a wider range of using distant mode (DX). When powered on, DX mode will be defaulted automatically; Press LOC button briefly to select Local mode and "LOCAL symbol on the LCD will light up for a few seconds. [. . . ]