User manual BOSS ONYX N1800.2

[. . . ] · To avoid risk of electronic shock or damage to the monitor, do not permit any of this equipment to become damp or wet from water or drinks. If this does occur, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible. · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power cord and send the monitor to your local dealer or service center as soon as possible . Safety precautions · Do not operate this equipment while driving ­ safe driving should always be your highest priority. [. . . ] In some states and countries, the viewing of images on a screen inside a vehicle is illegal, even by people other than the driver. Be sure that the installation and operation of this system is in compliance with local rules and regulations. Dangerous high voltages are present which may result in electric shock. · Do not attempt to repair a damaged, broken or faulty power cord. There are no user-serviceable parts within the unit. ONYX N1800. 2 User's Manual - page 2 Installation precautions Choose a mounting location in your vehicle where the unit will not distract or otherwise interfere with the driver's ability to control the vehicle. Do not install components in areas which are susceptible to rain, moisture, direct sunlight, extreme heat or cold, excessive dust, dirt or humidity. If installation requires drilling holes or other modifications to the vehicle, consult with your nearest dealer or professional car audio installer. Use only the installation parts and hardware provided with the unit to ensure proper installation. Run them to the location of the video source unit (such as a DVD player) and connect the wires as shown in the System Wiring diagram. ONYX N1800. 2 User's Manual - page 4 Remote Control Features 1 POWER Press to turn the monitor ON or OFF. 2 VIDEO SELECT 1 2 3 MENU VIDEO SELECT Use this button to switch between Video Source 1 and VIideo Source 2. 3 MENU BUTTON Press this button to enter the OSD (On-Screen Display) menu system for controlling various parameters for the display. 4 5 MODE SELECT 4 UP/DOWN BUTTONS These buttons are used to increase or decrease parameters in the on-screen display menu system. 5 MODE ONYX N1800. 2 This monitor features presets for Picture, Brightness, Color and Contrast. Press MODE to access these presets. Changing the battery in the remote control The remote battery is held in a small "drawer" on one edge of the remote. To open this drawer, press and hold the small button on the edge of this drawer (as shown below) and slide the drawer out. Insert a new battery and push the drawer back fully into the remote. Battery Release button ONYX N1800. 2 User's Manual - page 5 System wiring On a towel or soft cloth, gently place the monitor assembly "face down" on a stable worksurface. Using the wires provided, complete the audio, video and power connections in your vehicle as shown in the diagram below. VIDEO SOURCE 1 VIDEO INPUT 1 (YELLOW) (DVD player, video game, etc. ) VIDEO OUTPUT VIDEO SOURCE 2 VIDEO INPUT 2 (YELLOW) (DVD player, video game, etc. ) VIDEO OUTPUT RED FUSE BLACK 12V Battery to Chassis Ground ONYX N1800. 2 User's Manual - page 6 On-screen (OSD) menu system This monitor incorporates an on-screen menu display systems which permits you to setup the monitor for a wide variety of installations and applications. Enter the OSD menu system by pressing the MENU BUTTON on the front of the monitor or on the remote control. The monitor will display a menu with the following functions, which you can adjust individually: BRIGHTNESS: Makes the image more or less bright CONTRAST: Increases or decreases the image intensity COLOR: Makes the colors more or less saturated TINT: Permits you to shift the color range, making it greener or redder. RESET: Returns all settings to factor values EXIT: Allows you to exit the OSD system. The basic navigation method for this menu system is to: 1 - Press the MENU button to enter the OSD system. [. . . ] 4 - Press MENU to confirm the setting and move to other settings you wish to change. To exit the OSD system press the MENU button until you have highlighted EXIT and press MENU again. Display presets (Mode Button on Remote) This monitor features preset combinations of settings for Picture, Brightness, Color and Contrast (called Standard, Strong and Soft). (Note: Access to these presets is only available through use of the remote control). ONYX N1800. 2 User's Manual - page 7 Troubleshooting If you experience operation or performance problems with this product, compare your installation with the electrical wiring diagram on the previous page. [. . . ]