User manual BOSS JS-5 JAMSTATION

[. . . ] T. M. , PostScript T. M. , Adobe Systems Inc. ; Macintosh EtherTalk, LocalTalk, TrueType Reg. , Apple Computer Inc. ; Novell, NetWare, Unix, YES NetWare Tested and Approved logo, Reg. TokenRing, T. M. , International Business Machines Corp. ii BOSS OkiLAN 6020e User's Guide Organization and Contents Organization This manual has been divided into eight sections. Section I contains and installation instructions for the OkiLAN 6020e print server. [. . . ] Set the appropriate configuration by choosing the applicable file folder tabs. The following settings are configurable: · TCP/IP · EtherTalk · NetWare · Output Port · NetWare Port · SNMP · NetWare Queues · Protocols · VINES* · SNMP Traps * May apply to other OkiLAN print server models. IV - 24 BOSS OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP Configuring TCP/IP Options To configure options specific to the TCP/IP protocol, select the TCP/IP tab. The following screen will display: Fill in the following information: IP Address Resolution · Set Permanent - Select this option to make the IP address permanent. If the OkiLAN 6020e has been configured to remember its IP address, it does not need to determine its address each time it is powered on. The IP address must follow the format XXX. XXX. XXX. XXX, where each XXX is a number from 0 to 255. CAUTION: If you select an invalid IP address, you may not be able to access the OkiLAN 6020e. · Use Network Protocol - Select this option to use RARP, BOOTP or DHCP to determine the IP address at power up. Specify which protocol(s) to use. BOSS OkiLAN 6020e User's Guide IV - 25 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP Subnet Mask If your network environment includes subnets, you will want to set the subnet mask. The subnet mask must follow the format XXX. XXX. XXX. XXX, where each XXX is a number from 0 to 255. The OkiLAN 6020e interprets a subnet mask of 0. 0. 0. 0 or 255. 255. 255. 255 as no subnet mask specified. CAUTION: If you select an invalid subnet mask, you may not be able to access the OkiLAN 6020e. Default Gateway If your local network is attached to other networks, you can specify the address of your default gateway. The trap community name field is used by the OkiNet Alert and other network monitoring utilities for grouping or filtering OkiLAN 6020e devices. OkiNet Alert assists in managing network printers by immediately alerting you of printer problems. BOSS OkiLAN 6020e User's Guide IV - 31 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP Enabling/Disabling Protocols To enable or disable protocols on the OkiLAN 6020e, select the Protocols tab. If you disable a protocol, the OkiLAN 6020e will no longer communicate using that protocol. SNMP Trap Configuration The SNMP Trap option allows configuration of traps. Traps can be sent to an SNMP manager or be broadcast to all hosts on the local segment. To configure SNMP traps, select the SNMP Traps tab. Note: SNMP options need to be configured only if you are managing an OkiLAN 6020e or getting system information using SNMP. Protocol Select the protocol for which you wish to configure trap information. IV - 32 BOSS OkiLAN 6020e User's Guide Section 4 - Chapter 4 - OkiNet for TCP/IP Trap Destination · TCP/IP Protocol - Enter the IP address to which traps will be sent. The IP address must follow the format XXX. XXX. XXX. XXX, where each XXX is a number from 0 to 255. To broadcast traps to all hosts on the local subnet, enter 255. 255. 255. 255. · NetWare Protocol - Enter the network number and hardware address, respectively, to which traps will be sent. To broadcast traps to all addresses on all networks, enter FFFFFFFF (8 characters) in the first field and FFFFFFFFFFFF (12 characters) in the second field. To broadcast traps to all addresses on a specific network, enter the network number in the first field and then FFFFFFFFFFFF (12 characters) in the second field. Ports to Trap Select the output ports on which you wish traps to be active. Printer Traps Select the printer traps to be activated. The following printer error conditions may cause a printer trap to occur: · On-line · Off-line · No Printer Attached · Paper Out · Paper Jam · Door Open · Toner Low · Printer Error The toner low, door open and paper jam traps require that your printer be set to automatic emulation switching (the default) or PCL emulation. BOSS OkiLAN 6020e User's Guide IV - 33 TCP/IP Section 4 - Chapter 4 - OkiNet for TCP/IP Saving the Configuration Once all settings have been defined, select OK. [. . . ] The display is divided into two smaller panels: the Printer Filters Panel and the Printer Information Panel. The Printer Information Panel, on the right hand side of the main display, shows a list of all the printers currently available for status and configuration. Printer name and status information is detailed to the right of the printer icon. OkiView 32 Printer Properties Menu The Printer Properties menu allows you to get detailed status information and to configure printers. To enter the Printer Properties menu: 1 Select a printer on the Printer Information Panel. [. . . ]