User manual BOSS HAVOC REV665

[. . . ] If you lack adequate current, your music reproduction will be distorted. OUTLAW MOSFET Amplifier User's Manual - page 3 General precautions Before installing and using your new amplifier, please become familiar with all the information contained in this manual. Dangerous high voltages are present which may result in electric shock. · To avoid risk of electronic shock or damage to the amplifier, do not permit any of this equipment to become damp or wet from water or drinks. If this does occur, immediately unplug the power wires and send the amplifier to your local dealer or service center as soon as possible. [. . . ] · If there is smoke or any peculiar odor present during use or if there is damage to any of the component enclosures, immediately unplug the power wire and send the amplifier to your local dealer or service center as soon as possible . Before making or breaking power connections in your system, disconnect the vehicle battery. Confirm that your head unit or other equipment is turned off while connecting the input jacks and speaker terminals. If you need to replace the power fuse, replace it only with a fuse identical to that supplied with the amplifier. Using a fuse of a different type or rating may result in damage to your audio system or your amplifier which is not covered by the manufacturer's warranty. Mounting the amplifier 1. Find a suitable location in the vehicle in which to mount the amplifier. Make sure there is sufficient air circulation around the intended mounting location. Mark the location for the mounting hole screws by positioning the amplifier where you wish to install it. Use a scribe or mounting screw, inserted through each of the amp's mounting holes, to mark the mounting surface. It is designed ONLY to match the output level of your audio source to the input level of your amplifier. Do not adjust this input level to maximum unless your input level requires it. Ignoring these instructions will result in an input overload to the amplifier, and excessive audio distortion. It can also cause the protection circuit to engage. OUTLAW MOSFET Amplifier User's Manual - page 5 Low Level Input Wiring Low-level (RCA) input wiring is preferred for best audio performance. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! 4-Channel Amplifiers OL1800 and OL2400 Remote Subwoofer Level Control CH1/2 BASS BOOST INPUT LEVEL + CH1 CH2 LOW LEVEL INPUTS CH3 CH1 CH1/2 CROSSOVER FREQ 40Hz LOW PASS 150Hz FULL RANGE FULL RANGE HIGH PASS MODE HIGH PASS + HIGH INPUTS BASS BOOST INPUT LEVEL REMOTE SUBWOOFER LEVEL CONTROL + CH 3/4 CH4 CH3 + CH 3/4 CROSSOVER CH4 CH2 40Hz LOW 150Hz PASS HIGH INPUTS FREQ MODE To REAR Audio Outputs of head unit or signal processor To FRONT Audio Outputs of head unit or signal processor OUTLAW MOSFET Amplifier User's Manual - page 6 High Level Input Wiring The high level input(s) should only be used when your head unit lacks RCA outputs. If the RCA outputs are not present, connect the speaker outputs from the receiver to the high level input connector of the amplifier. NOTE: Do not connect BOTH the high level and low level inputs from your receiver to your amplifier at the same time! To Speaker Terminals of head unit 4-Channel Amplifiers OL1800 and OL2400 CH CH CH CH 1+ 1- 2- 2+ CH1/2 BASS BOOST INPUT LEVEL + CH1 CH2 LOW LEVEL INPUTS CH3 CH1 CH1/2 CROSSOVER FREQ 40Hz LOW PASS 150Hz FULL RANGE FULL RANGE HIGH PASS MODE HIGH PASS + HIGH INPUTS BASS BOOST INPUT LEVEL REMOTE SUBWOOFER LEVEL CONTROL + CH 3/4 CH4 CH3 + CH 3/4 CROSSOVER CH4 CH2 40Hz LOW 150Hz PASS HIGH INPUTS FREQ MODE Remote Subwoofer Level Control CH CH CH CH 3+ 3- 4- 4+ To Speaker Terminals of head unit OUTLAW MOSFET Amplifier User's Manual - page 7 Power and Speaker Wiring 4 Channel Mode 4-Channel Amplifiers OL1800 and OL2400 SPEAKER IMPEDANCE 2-8 OHMS CH1 Speaker CH2 Speaker Four Channel Mode CH 4 + CH 3 + CH 2 + CH 1 + SPEAKER CONNECTIONS CH3/4 BRIDGED MODE + CH1/2 BRIDGED MODE + Chassis ground point to REMOTE TURN-ON terminal of head unit Battery FUSE CH4 Speaker CH3 Speaker SPEAKER IMPEDANCE 2-8 OHMS OUTLAW MOSFET Amplifier User's Manual - page 8 Power and Speaker Wiring Bridged Modes 4-Channel Amplifiers OL1800 and OL2400 Connect the Negative (-) terminal of the RIGHT subwoofer to the CH2 (-) amplifier terminal. RIGHT Subwoofer Connect the Positive (+) terminal of the RIGHT subwoofer to the CH1 (+) amplifier terminal. SPEAKER IMPEDANCE 4-8 OHMS Bridged Mode CH4 + CH3 + CH 2 + CH1 + SPEAKER CONNECTIONS CH3/4 BRIDGED MODE + CH1/2 BRIDGED MODE + LEFT Subwoofer Chassis ground point Connect the Negative (-) terminal of the LEFT subwoofer to the CH4 (-) amplifier terminal. Connect the Positive (+) terminal of the LEFT subwoofer to the CH3 (+) amplifier terminal. to REMOTE TURN-ON terminal of head unit Battery FUSE SPEAKER IMPEDANCE 4-8 OHMS OUTLAW MOSFET Amplifier User's Manual - page 9 Power and Speaker Wiring Tri-Mode 4-Channel Amplifiers OL1800 and OL2400 Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. [. . . ] Connect the Positive (+) terminal of the LEFT subwoofer to the CH3 (+) amplifier terminal. to REMOTE TURN-ON terminal of head unit Battery FUSE SPEAKER IMPEDANCE 4-8 OHMS OUTLAW MOSFET Amplifier User's Manual - page 9 Power and Speaker Wiring Tri-Mode 4-Channel Amplifiers OL1800 and OL2400 Tri-mode operation allows you to connect this amplifier to a pair of main speakers plus a subwoofer on one pair of output channels. The main speakers will operate in STEREO while the subwoofer simultaneously operates in MONO. To set up the amplifier to run in this mode, put the crossover switches in the FULL position. Insert high pass filter capacitors and a low pass filter inductor into the wiring as shown below. [. . . ]