User manual BOSS FC-50 MIDI FOOT CONTROLLER

[. . . ] To select playback mode Press MODE button to select a different mode of operation as indicated on the display panel. To adjust the volume level To increase the volume, rotate the volume knob clockwise. When the volume is adjusted, the volume level will be shown on the display panel as a number ranging from 0 (lowest) to 46 (highest). To mute or resume the sound Press MUTE button momentarily to mute the audio volume, and MUTE will flash in the display. [. . . ] To store the current station or turn on the preset station Under RADIO mode: A) Press one of 1-6 number buttons hold for more than 1 second until the second beep output to store the current station in the preset memory bank of the number button for the current band. B) Press one of 1-6 number buttons shortly to turn on the preset station stored in the preset memory bank of the number button for the current band. To automatically store for the strongest stations and scan for each stored stations Under RADIO mode: A) Long press the AS/PS button, it will search from the current frequency and check the signal strength until 1 cycle search is finished on current band, and then 6 strongest stations will be preset to the corresponding preset memory banks of the 6 number buttons. When the auto-storage operation is completed, it will turn on the preset station stored in the memory bank of the 1 button. B) Short press the AS/PS button to scan for each preset station for the current band. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset station for 5 seconds with releasing mute, while memory digital and frequency will flash on LCD, and then scan again. To scan for strong signal of radio station Press SCAN button to scan up by one channel step with station detection. If a valid signal has detected, the current frequency is blinked within 5 seconds, then press it again to stop scan and remain the current frequency; otherwise, the unit continue to scan up by one channel step with station detection 5 seconds later. STEREO/MONO BUTTON In FM mode, press the MO/ST button to select the STEREO or MONO sound mode. CARE FOR USING CD'S: About CD-R/CD-R/W discs: In addition to commercially-recorded audio CD's, this unit can play CD-R and CD-R/W discs. In come cases, particularly when recorded on older CD burners, some CD-R and CD-R/W discs may not play. Also, whenever you are recording a CD for playback in this receiver, it is recommended that you record at 24x or slower speed for CD-R and 4x or slower for CD-R/W to achieve higher signal quality and better playback performance. A) Under TRACK SEARCH mode, the LCD will display TRK T 000 and flash the biggest digit 0 that the USB storage or MP3/WMA disc contain. Then rotate the VOL knob on the front panel or hold the + or - button on the remote controller to select the number of the flashing digit from 0 ~ 9. Then press SEL button to confirm the number and flash next smaller digit 0. After finishing selecting the number of all flashing digit, press SEL button to play the track of the selected serial number. B) Under DIRECTORY SEARCH mode , the LCD will display the root folder(if there is not the root folder, it will find a root folder named ROOT). Then rotate VOL knob or press the + or - button to select your desired folder and then press the >>|/|<< button to select your desired track in the folder. Finally press the SEL button to play the selected track. WIRING CONNECTION BLUE TOOTH ANT ANTENNA PLUG AUX LINE IN (BROWN) 10A FUSE FILTER BOX 0. 5A FUSE RED R WHITE L RED R WHITE L RED R WHITE L YELLOW FRONT RIGHT SP REAR CONSTANT 12 VOLTS GROUND YELLOW BLACK RED RCA LINE OUT REAR(GRAY) RCA LINE OUT FRONT(BLACK) WOOFER LINE OUT IGNITION SWITCH 12 VOLTS BLUE AUTO ANT FRONT LEFT SP REAR WHITE WHITE/BLACK GREEN GREEN/BLACK GRAY GRAY/BLACK VIOLET VIOLET/BLACK NOTES: 1. Ensure that the blue auto antenna cable does not make contact with any ground connection. Front AUX IN and rear AUX IN can not be connected to at the same time. 7 12 PDF created with FinePrint pdfFactory trial version http://www. pdffactory. com BATTERY INFORMATION OF REMOTE CONTROL Replace Battery in Remote Control : 1. Before using the remote control for the first time, pull the insulating sheet out of the remote control as the direction indicated by the arrow. (see fig. 1) 2. Press the movable block hold as the direction indicated by the A arrow (See fig. 2), then pull the battery holder out of the remote control as the direction indicated by the B arrow(see fig. 2). 3. Replace the old battery by a new battery with (+) polarity side upward. 4. Insert the battery holder to the original position in remote control. [. . . ] Note: (1) CONN OK appears on LCD upon successful connection; NOT CON appears on LCD if connection fail. (2) The Bluetooth LED indicator on the front panel indicates the three connection status: -LED Turn off: No connection at all -LED Blinking: Connection status -LED Turn on: Talking status (3) Bluetooth icon appears on LCD only when in connection status. (4) In the connection status: Mobile phone transfers to the car audio whenever a dialling takes place; Mobile phone transfers to the car audio whenever receiving a call. Dialling when in connection status A) Dial with the mobile phone directly. [. . . ]