User manual BOSS DVD9900B

[. . . ] Please keep this manual in a safe place for future reference. Installation precautions Choose a mounting location in your vehicle where the unit will not distract or otherwise interfere with the driver's ability to control the vehicle. Before final installation, temporarily connect the wiring according to the diagram near the end of this manual, check it to ensure that it has been connected properly, and test the unit to make sure it is working correctly. Use only the installation parts and hardware provided with the unit to ensure proper installation. Using other parts can cause malfunction and possible damage to your DVD player. [. . . ] Each time the button is pressed, the scene will be played from a different angle. 21 AUDIO Press this button to select the language to be played back on the disc. Each press of the button will provide the audio in a different language (if available). 22 DISPLAY Press this button to show the total elapsed or remaining playing time. DVD470B/DVD490T User's Manual - page 7 Remote Control Battery Replacement Slide open the battery door on the remote as shown below. Insert two AAA batteries, observing proper polarity as shown on the battery door. Replace the battery door. Remote IR Sensor If you need to mount the DVD player in a location which is inaccessible, or where the line-of-sight between the remote control and the face of the player is interrupted, connect the Remote Sensor as shown in the diagram below. Mount the Remote Sensor in a convenient location which is in direct line-of-sight with the use location of the remote control. Point the remote control at the sensor to operate the player. DVD470B/DVD490T User's Manual - page 8 A/V Output Connections to Video Monitor This disc player sends video output signals simultaneously to both the S-Video and the RCA Video outputs. Please connect the player using one of the two methods shown. Using standard video output (RCA type) DVD Player Video Monitor ­ OR ­ Using S-Video output DVD Player Video Monitor S-VIDEO CABLE DVD470B/DVD490T User's Manual - page 9 A/V Input Connections (using Front Panel Inputs) This disc player offers you the option of using the auxiliary front panel A/V input jacks to connect a video game, digital camera/camcorder or other units you wish to use in your mobile video system. A/V Input Source Video Game, Camera, etc. DVD Player TV SET RED WHITE YELLOW DVD PLAYER TV Antenna Connection (DVD490T only) DVD Player DVD470B/DVD490T User's Manual - page 10 Amplifier Connections This disc player offers you a choice of analog (RCA) or digital (coaxial) audio outputs to connect to your amplifier. Using standard audio output (RCA type) TV SET DVD PLAYER AUDIO INPUTS ­ OR ­ Using Digital Audio (coaxial) output AUDIO INPUTS DVD470B/DVD490T User's Manual - page 11 Vehicle Power Connections Follow the connection diagram below. The cable provided for this connection has two inline fuses and a choke assembly with fuse. Please note: The yellow wire should be connected directly to the vehicle's battery. +12V DC (BATT +) YELLOW Ground (BATT -) BLACK Choke Box Ignition switch RED (ACC +) Remote out BLUE About the power receptacle The power receptacle for the DVD player is shown at left. This output is for use as an extra ON/OFF control for an external amplifier or other device. DVD470B/DVD490T User's Manual - page 12 TV Mode setup (DVD490T only) To set up the DVD player to use in the TV Tuner mode, press MODE once. The player will automatically scan for and memorize the available TV channels. The screen will display a menu of items from which to select from for that particular disc. Please note: This feature is only available on certain kinds of discs. The first step in programming is to turn off the PBC mode, and press the STOP button. The feature is now ready and the screen displays the following: ADJUSTING BASS, TREBLE AND BALANCE Press ENTER to enter the Settings selection mode. If there is no entry made within 5 seconds of the pressing of the ENTER button, the player will automatically exit the Settings selection mode. Press the keys to select the BASS setting, then press the buttons to adjust the bass level between -12 and +12. In a similar manner, you can use the buttons to access the settings for Treble and Balance. Program : P00:00 Press the number key to enter the number of the chapter(s) or track(s) to be played. For example, to play track 5, followed by tracks 3 and 6, enter 5, 3, 6. Press PLAY and the selected chapters and/or tracks will be played. DVD470B/DVD490T User's Manual - page 16 MP3 Playback Playback of MP3 files on this player may be done in one of two different modes: 1­ "with menu" mode 2­ "no menu" mode The factory default for this player is the "without menu" mode. If you wish to change the MP3 playback mode, please refer to the Settings section in the column entitled "SmartNav Settings" instructions on how to do so. "NO MENU" MP3 PLAYBACK This mode is also called "first play" mode. After a disc is inserted and is read, the player will stop, and display "STOP" on the front panel. [. . . ] The PCM system incorporates additional decoding processes which may enhance the viewing. Use the buttons to highlight "Audio Setup. " Press the ENTER button, and the following screen will be displayed: PARENTAL GUIDANCE Parents who wish to limit their children's viewing content based on its rating (e. g. , PG-13) can set up a password-based system to limit the player to only showing movie programs at or below this rating. Begin this setup procedure by making sure there are no discs in the player. Use the buttons to highlight "Preferences" and then press ENTER. [. . . ]