User manual BOSS BV56HR

[. . . ] We hope you enjoy using this product and encourage you to always listen at a moderate, safe sound level to avoid any possible hearing damage or loss. If you listen to excessively loud sound over time, your hearing can adapt to higher volumes and what sounds "normal" to you may be quite harmful and can cause you to have permanent hearing loss. So please practice "safe sound" and always listen at moderate sound levels only. Start with your volume control at the lowest setting, and slowly increase the level until you can hear it comfortably and clearly, free from distortion. [. . . ] When PI information is not received for retune time, the radio will search for the next, same PI station. When same PI station is not received during 1 cyclic search, the radio will switch to the last station and wait 4-5 minutes for PI code. 4) MASK DPI/MASK ALL: MASK DPI mode: only AF which has different PI is masked. MASK ALL mode: AF with different PI and NO RDS signals with high field strength levels are masked. 5) BEEP 2ND/BEEP ALL/BEEP OFF: BEEP 2ND mode: the beep is only generated when an allotted double key is pressed long(1second). BEEP ALL mode: the beep is generated when every key is pressed(except power and release buttons). 6) SEEK1/SEEK2: SEEK1: pressing and holding UP/DOWN buttons will search for strong signal stations, and will stop at the first strong signal. SEEK2: pressing and holding UP/DOWN buttons will enter search mode, and will only stop searching when the button is released. To reset the unit When the LCD displays wrongly or some function knobs are disable, press the REL button to flip down the front panel and then take it away from the unit chassis. Push the RESET button with one needle analog to reset the distorted program to zero. To take away the front panel Press the REL button to flip down the front panel and then take it away from the head unit. Segment flashing: AF switching mode on, but RDS information is not received yet. When AF switching mode is selected, the radio checks the signal strength of AF all the time. The interval of checking time of each AFs depends on the signal strength of current station, from a few minute for strong station to a few seconds for weak station. Every time that new AF is stronger than current station, it switches over to that frequency for very short time, and NEW FREQUENCY is displayed for 1-2 second. Because the mute time of AF switching or checking time is very short, it is almost inaudible in case of normal program. If AF and TP flash on LCD, it can only search for traffic announcement station). During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only receive and save RDS program. When pressing and holding the AF button, AF mode is converted to REGION ON/OFF mode. REGIONAL MODE ON: AF switching or PI SEEK is implemented to the station which have all PI codes are same as current station. (PI CODE is checked when AF CHECK in progress) REGIONAL MODE OFF: The regional code in the format of PI code is ignored when AF switching or PI SEEK is implemented. (PI CODE and COVERAGE AREA is not checked when AF CHECK in progress) UNIT CHASSIS PLASTIC TRIM RING DASHBOARD METAL MOUNTING SLEEVE EJ FRONT PANEL To remove the unit out of the metal mounting sleeve, insert the two supplied KEYS into the left and right side slots of the chassis at the same time. Then pull the chassis out of the metal mounting sleeve as shown in the right illustration. NOTE Before mounting and operating the CD player, remove the metal mounting sleeve illustrated by the arrows. Remove the two screws that fix the CD deck mechanism player during transportation before mounting the player. To attach the removable faceplate back to the unit chassis, firstly join the left guide block hole to the left cylinder, then join the right guide block hole and the right cylinder, finally flip the front panel up to combine with chassis. EJECT (EJ) BUTTON Push this reset button with a cuspidal object to renovate the distorted program once the program is distorted. RESET BUTTON To remove the front panel, after flipping down the front panel, push it rightwards firstly, then draw the left of the front panel outwards. Before inserting or ejecting disc, press the REL button to flip down the faceplate. 13 6 8. [. . . ] Under CD/MP3/WMA disc mode, press INT button shortly to display S-INT and play the first 10 seconds part of each track of all. Under USB or MP3/WMA disc mode, press INT button long to display D-INT and play the first 10 seconds part of each in current folder. Under INT mode, press INT button again to stop INT mode and retain playing the track currently selected. To repeat track(s) Under USB mode, press RPT button shortly to display M-RPT and play the current track repeatedly. [. . . ]