User manual BOSS BV-650M

[. . . ] 13 Operating when the monitor stretching out . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Menu control operation in radiomode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Menu control operation in CDC mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . CAUTION: Please read and observe all warnings and instructions given is this owner's manual. [. . . ] Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery's negative (-) terminal. WIRING CONNECTION DIN REAR-MOUNT (Method B) 3 1 2. Remove the metal strap attached the back of the unit (if attached). 3. Lift the top of the outer trim ring then pull it out to remove it. I VIDEO YELLOW MAIN UNIT I 4. Insert both of the supplied keys into the slots at the middle left and right sides of the unit, then pull the unit out of the dashboard. M R N A L REMOTE CONTROL To the TV unit SWITCH (ACC+) 1. 4. Factory radio mounting bracket Car radio mounting bracket Screw After aligning the car radio mounting bracket with the factory radio mounting bracket, tighten the screws (5x5mm) at 2 places on each side. When fix factory radio mounting bracket with the screws, use a standard-tipped screwdriver to bend open the tabs of the car radio mounting bracket to make them fit into the holes in the factory radio mounting bracket. FRONTLch SPEAKER 1I WHrrVsLACK GREEN I La I' SYNC IN ; : ;0 BLUE :: ;; POWER ANTENNA FRONT Rch SPEAKER GREYIBLACK VIOLET SPEAKER GREENIBLACK Note: The Brake 1 wire is designed to connect to the ground wire, and the Brake 1 wire is designed to connect to CPU. Be sure that these two wires can't be connected to other wires, especially the ACC+ wire and the B+ wire. OPERATION LOCATION AND FUNCTION OF KEYS OPERATION LOCATION AND FUNCTION OF KEYS Fig. / I 4 (OpenIClose button) MUTE LCD TFT Monitor SEL VOLUME+ VOLUMEReset button 11. 53. PAU INT RPT RDM CDCD+ (?, POWER OPEN 0-9 Numeric Button MI-M6 LOC -I-- (SCAN) BAND W/AV MODE MUTE DlSP MENU TUNICH A / I VOL41, ASIPS PANEL+ PANELEQ LOUD ST/MO OPERATION Adjusting the loud - In loud mode, use VOLUME + I buttons (7&8) or VOL 4 / b buttons (47) to switch between loud on and off. Press it again to release the function. OPERATION - - Radio Operation Switching to radio mode Press MODE button (12) on the front panel or MODE button (42) on the remote control to select radio mode, the radio mode appears in the display together with the memory band and frequency. Selecting the frequency band Press BND button (11) on the front panel or BAND button (40) on remote control to select desired band. The reception band will change in the following order: Adjusting the equalization - In equalization mode, use VOLUME + I- buttons (7&8) or VOL 4 / b buttons (47) to switch between the following mode and the corresponding information appears on the LCD (4). r+ FLAT --c POP --c JAZZ -+ CLAS L 2 1 T FM1+ FM2 +FM3 +AM1 +AM2 1 - Directly press EQ button (51) to turn on equalization function and to select desired audio mode as above. Mute Press MUTE button (3) on the front panel or MUTE button (43) on remote control to cut down sound output. Setting the clock Press DlSP button (44) to change the display into clock display. While the current time is appeared on the LCD (4), press it again to return to frequency showing. Holding down DlSP button (44) for several seconds, and the time for hours is blinking on the display (4), then press VOLUME + I buttons (7&8) or V O L 4 / bbuttons (47) to switch between hours and minutes. Press TUNE + I- buttons (13&14) or TUNICH A / Vbuttons (46) to adjust the hours or minutes. Selecting station During radio mode, press TUNE + button (13) or TUNICH A button on remote control to increase frequency or TUNE - button (14) or TUNICH V button on remote control to decrease frequency by one step of channel spacing. - on , , < Automatically memory storing & program scanning - Automatic memory storing Press ASIPS button (48) for several seconds, the radio searches from the current frequency and checks the signal strength until one cycle search is finished. And then 6 strongest stations are stored into the corresponding preset number button. - Program scanning Press ASIPS button (48) shortly to scan preset station. When the field strength level is more than the threshold level of stop level. The radio is holding at that preset number for several seconds with release mute, then searches again. LocalIDistance Press LOC button (38) on remote control to select between local and distant stations. [. . . ] BRIGHT - Press digital select button (-/--) (39) CONTRAST cooperatively used with numeric buttons to select channel desired. For example, when you want select 16 channel, press -/-- (39) to switch I I [ NTSCSYS~): between "-" and "--" when the "-- ht i ; ; ; (;ht r " appears on the display, you can press "1 " button then press "6" BRIGHT button to select 16 channel. CONTRAST Menu control operation TlNT In Nmode: Press MENU button (19) or (45). Press TUNICH A / buttons (46) to (For the unit with PAL system): select the item upward or downward. [. . . ]