User manual BOSS 740UA

[. . . ] To prevent direct exposure to laser beam, do not try open the enclosure. Visible and invisible laser radiation when open and interlocks defeated. To protect our environment, do not dispose of electrical equipment in the domestic waste. Please return any electrical equipment that you will no longer use to the collection points provided for their disposal. [. . . ] Do not expose the disc to direct sunlight or nearby heat sources such as heating vents, caliduct which can cause the disc to warp. Do not leave disc in a car if it is parked in direct sunlight as that will lead to a considerable rise in the temperature inside the car. Do not use any secondhand or rented disc, usually, there is glue on the surface of those discs, it will stop the unit working and damage it. 5. Scratched up discs will produce poor sound performance and cause CD player to skip. In raining day or wet area, the moisture may form on the disc or the optical parts, The playback may not be possible. If moisture forms on the optical parts of the unit, allow the unit to sit for about one hour with power on. 7. Commercially available cleaners or anti-static spray will damage the unit. PDF created with FinePrint pdfFactory trial version http://www. pdffactory. com INSTALLATION METHOD This is an anti-theft installation method. Please connect the wiring, eg, the Power Supply, the Speakers and the Antenna according to the requirements of this Instruction Manual, then install the metal mounting sleeve into the car as per the diagram illustrated below. METAL S UPPORT S TRAP To boost up the capability of anti-jamming, please make sure fix tightly the metal support strap into the metal joint that connect to the chassis of the car. To properly fix the meal mounting sleeve, bend the tabs of the sleeve against the DASHBOARD with a screwdriver. B) To select and adjust the menu mode: Press SEL button long to turn on MENU mode, and the LCD will display BEEP 2ND/BEEP ALL/BEEP OFF, then press SEL button shortly and repeatedly to select SEEK1/SEEK2(in RADIO mode), DSP OFF/FLAT/POP M/CLASSICS/ ROCK, SUBW ON/OFF, VOL LAST/ VOL ADJ and ESP 6 / ESP 25 in the sequence and circulation. After selecting a desired mode, rotate the VOL knob on the front panel or press the + or - button to select one setup item of the desired mode. C) BEEP 2ND/BEEP ALL/BEEP OFF: BEEP 2ND mode: the beep is only generated when an allotted double key is pressed long(1second). BEEP ALL mode: the beep is generated when every key is pressed(except power and release buttons). D) SEEK1/SEEK2: SEEK1: press >>| or |<< button hold to seek up or down for the strong signal station. SEEK2: press >>| or |<< button hold to seek up or down for the strong signal station. After release it and then received the strong signal station, the seek will stop. E) DSP OFF/FLAT/POP M/CLASSICS/ROCK To select a preset EQ mode or turn off it. UNIT CHASSIS PLASTIC TRIM RING DASHBOARD METAL MOUNTING SLEEVE FRONT PANEL To remove the unit out of the metal mounting sleeve, insert the two supplied KEYS into the left and right side slots of the chassis at the same time. Then pull the chassis out of the metal mounting sleeve as shown in the right illustration. NOTE Before mounting and operating the CD player, remove the metal mo unting sleeve illustrated b y the arrows. Remove the two screws that fix the CD deck mechanism player during transportation before mounting the player. To attach the removable faceplate back to the unit chassis, firstly join the left guide block hole to the left cylinder, then join the right guide block hole and the right cylinder, finally flip the front panel up to combine with chassis. F) VOL LAST/ VOL ADJ VOL LAST: During playback, turn off the power and then turn on the power again, at the time, the volume level will be the one before turn off the power. VOL ADJ: When it is in VOL ADJ mode, the next mode will be A-VOL after VOL ADJ mode, then you can adjust the defaulted volume level. When the auto-storage operation is completed, it will turn on the preset station stored in the memory bank of the 1 button. B) Short press the AS/PS button to scan for each preset station for the current band. When the field strength level is more than the threshold level of stop level, the radio is holding at that preset station for 5 seconds with releasing mute, while memory digital and frequency will flash on LCD, and then scan again. To scan for strong signal of radio station Press SCAN button to scan up by one channel step with station detection. If a valid signal has detected, the current frequency is blinked within 5 seconds, then press it again to stop scan and remain the current frequency; otherwise, the unit continue to scan up by one channel step with station detection 5 seconds later. [. . . ] Then rotate VOL knob or press the + or - button to select your desired folder and then press the >>|/|<< button to select your desired track in the folder. C) Under FIRST CHARACTER SEARCH mode, the LCD will display A--. . . . . . , If there are files names its first character are A , the . . . . . . is the first file name its first character is A by the order of A~Z and 0~9; otherwise, the . . . . . . is NONE. Rotate the VOL knob or press the + or - button to select file s first character by the order of A~Z and 0~9. Then press the >>|/ |<< button to select one file its first characters is the selected one. [. . . ]