User manual BOSS 639UA

[. . . ] Press the reset button if the error code does not disappear, consult your nearest service dealer. Mechanism Error ERROR 2 Servo Error If at any time in the future you should need to dispose of this product please note that Waste electrical products should not be disposed of with household waste. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive) - 16 - -1- Handling Compact Discs MOISTURE CONDENSATION On a rainy day or in a very damp area, moisture may condense on the lenses inside the unit. In such a case, remove the disc and wait for about an hour until the moisture has evaporated. Specifications Supply voltage Current consumption Discs played Audio Signal Output Characteristics 12V DC(11V-15V) Less than 15A Compact disc 5 (12 cm) disc 2ch line out (1) Frequency Response: 20Hz-20kHz (2) S/N Ratio: 40 dB (JIS) (3) Wow and Flutter: Below measurable limits NOTES ON CDs 1. To keep the disc clean, do not touch the surface (P . 1). NOTES ON DISCS If you use the discs explained below, the sticky residue can cause the CD to stop spinning and may cause malfunction or ruin your discs. [. . . ] 5. 2 4 Dashboard Nut (5mm) Screw (5x15mm) Screw Support Strap Be sure to use the support strap to secure the back of the unit in place. The strap can be bent by hand to the desired angle. - 14 - -3- Removing the unit Wiring Diagram (12 Pin Harness Plug) a b c a. Insert fingers into the groove in the front of frame and pull out to remove the frame. (When re-attaching the frame, point the side with a groove down wards and attach it. ) c. Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click. Pulling the levers makes it possible to remove the unit from the dashboard. R-OUT R-IN ANT L-OUT L-IN Trim Plate Installation: Push the trim plate against the chassis until it is fitted . You must do this before you install the front panel, otherwise it can't be attached. ANT JACK 12-PIN AUDIO/POWER HARNESS 1 2 3 4 5 6 7 8 9 10 11 12 Figure 1 Pin View PIN 1 2 3 4 5 6 WIRE COLOR VIOLET VIOLET/BLACK GREY GREY/BLACK WHITE WHITE/BLACK FUNCTION/LABEL RIGHT FRONT SPEAKER(+) RIGHT FRONT SPEAKER(-) LEFT FRONT SPEAKER(+) LEFT FRONT SPEAKER(-) RIGHT REAR SPEAKER(+) RIGHT REAR SPEAKER(-) PIN 7 8 9 10 11 12 WIRE COLOR GREEN GREEN/BLACK BLUE/WHITE RED BLACK YELLOW FUNCTION/LABEL LEFT REAR SPEAKER (+ ) LEFT REAR SPEAKER (-) POWER ANTENNA IGNITION(ACC) CHASSIS GROUND BATTERY(+ ) -4- - 13 - Setting the clock Detachable Control Panel(D. C. P) Removing The Detachable Control Panel (D. C. P. ). 1. 1. Attach the panel at the right side first, with point B on the main unit touching point A on the D. C. P (As shown on the digram). unit until a click sound is heard. B To change the clock setting, press and hold the ENTER button (2). Setting the time After pressing ENTER, to change the time, press I<< / >>I (1) to correct the time. Setting the time display mode After pressing ENTER, to switch between 24 hour mode and 12 hour mode ( AM/PM mode), by pressing and hold ENTER until the display mode changes. CAUTION DO NOT insert the D. C. P from the left side. After removing it, place it in a protective case and be careful not to drop it or subject it to strong shocks. When the release button is pressed and the D. C. P is unlocked, the car's vibrations may cause it to fall. To prevent damage to the D. C. P always store it in a protective case after detaching it. , The rear connector that connects the main unit and the D. C. P is an extremely important part. Be careful not to damage it by pressing on it with fingernails, pens, screwdrivers, etc. Socket Note: If the D. C. P is dirty, wipe off the dirt with soft, dry cloth only. And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the D. C. P . - 12 - -5- General And Radio Control 2 1 6, 10 8 using remote control. . . . 1. ) I<< and >>I (Skip back/skip forward, fast back/fast forward) Press those buttons to skip back or ahead one track. Press and hold for fast back or fast forward. 4 2. ) RDM (Random Play Mode) Press this button to play all MP3 files in random order. Press and hold again to turn off Loudness function. 3. ) STOP Press to stop playback. Press PLAY PAUSE to begin playback on the first track (NOT the track on last play) 4. ) PLAY/PAUSE Files will begin to play automatically. 5. ) RPT (Repeat Play Mode) Press this button to repeat all the playback automatically. [. . . ] Press again to cancel. 3 6 4 SD RESET 5 7 1. ) PLAY Files will begin to play automatically. Press PLAY to begin playback on the first track (NOT the track on last play) 3. ) PAUSE Press to pause playback. Press PLAY to resume playback from last play 4. ) SCAN (Intro Scan) To audition the first 10 seconds each track, press this button. 5. ) REPEAT (Repeat Play Mode) Press this button to repeat all the playback automatically. [. . . ]