User manual BOSS 614C

[. . . ] Do not use solvents such as benzine, thinner, commercially available cleaners, or antistatic spray intended for analog discs. Only for this unit. CD-Rs and CD-RWs which have not undergone finalization processing cannot be played. (For more information on finalization processing, refer to the manual for your CD-R/CD-RW writing software or CD-R/CD-RW recorder. ) Additionally, depending on the recording status, it may prove impossible to play certain CDs record on CD-R or CD-RW. E-2 3. INSTALLATION Before finally installing the unit, connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly. [. . . ] BASIC OPERATIONS 1) PANEL RELEASE BUTTON (REL) Press this button to remove the control panel. 12) POWER ON/OFF BUTTON Press this button to turn on or off the power. 5) DISPLAY BUTTON (DISP) Press this button briefly, the LCD will display the clock for about 2 seconds, then return to previous display mode. Clock Adjustment Under clock display mode, press DISP button until the LCD flashes, press Tuning Up Button to adjust hour and Tuning Down Button to adjust minute. 16) SOURCE BUTTON (SOURCE) Press this button to select Radio and CD modes. The available selections depends on version: Radio CD Player Radio > CD > AUX in Sub-woofer On/Off Press SOURCE button for more than 3 seconds to activate or turn off the Sub-woofer output. Aux Input Connect the external signal to the auxiliary line in jack located at the rear of the unit , then press Source button to select Aux mode. Press Source Button again to cancel Aux Mode and return to previous mode. RESET BUTTON The RESET button is located on the main unit (as shown on the diagram). To press it vertically with a ballpoint pen or metal object will activate it. The reset button is to be activated for the following reasons: Initial installation of the unit when all wiring is completed. Note: If the unit cannot function normally after reseting, please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the control panel. E-7 7. AUDIO OPERATIONS 10) VOLUME KNOB Turn this knob to adjust desired volume level. 4) AUDIO BUTTON Press this button to select desired audio function. ORDER OF FUNCTION: VOLUME(VOL) -> BASS(BAS) -> TREBLE(TRE) ->BALANCE(BAL) ->FADER(FAD) While the selected function is displayed, turn Volume Knob to adjust the level within 5 seconds, otherwise the unit will return to volume adjustment mode. 17) PRESET EQUALIZER BUTTON (EQ) Press this button to toggle the following EQ settings: FLAT->CLASSICS->POP M->ROCK M->DSP OFF At DSP OFF mode, EQ will be controlled by Bass/Treble setting. 13) BAND/LOUDNESS BUTTON (BAND/LOUD) Press the Band/Loudness Button for couple of seconds to switch the loudness on or off. When Loudness is on, display will show 'Loud On' for a few seconds. E-8 8. RADIO OPERATIONS 11) AUTO MEMORY STORE/PRESET SCAN BUTTON (AS/PS) 1. PRESET SCAN: Press AS/PS button briefly to enter Preset Scan mode, it will scan all the preset stations in the memories, you can hear that it will stay on each station for about 5 seconds. 2. AUTO MEMORY STORE: Press AS/PS button for couple of seconds to enter Auto Store mode, this feature will automatically scan the current band and enter up to 6 strongest stations into the 6 preset memories. 7) STATION PRESET BUTTONS (M1-M6) 1. Press these buttons briefly to recall the stored stations in the selected band. 2. Presetting stations manually, Press the BAND button to select the band for the stations to be preset. Press the Preset button at which you want to store the station for at least 2 second. The preset number will appear on the display accompanied by a beep, this indicates that the station has been stored into memory. [. . . ] If any of the problems persist after check list has been made, consult your nearest service dealer. Symptom No power Cause The car ignition is not on. Solution If the power supply is properly connected to the car accessory terminal, switch the ignition key to "ACC" Replace the fuse. Front panel is not properly fixed into its place Adjust the installation angle to less than 30 degrees. The fuse is blown. Disc cannot be loaded or ejected Presence of CD disc inside the player. [. . . ]